pcb with smd mounted CC regulator - newbie project guidance please

Hello, this is my 1st post! I am totally new to all of this and have a very simple project that consists of a single board mounted smd constant current regulator for driving LEDs. The board has in/out solder pads that are connected by copper pour to their respective component solder pads. I've tried to manually panelize the pcb. For now it's just a 2x2, but I will eventually need to extend the array to fall within JLCPCB's minimum/maximum board size requirements for doing v-cuts. I've drawn the board outline and the v-cuts with appropriate width trace lines per

https://jlcpcb.com/capabilities/Capabilities



and have annotated the v-cuts on the mechanical layer. When I tried to use the EasyEDA Panelize function, the v-cut annotations appeared on the same Board Outline layer (I read that this needs to be on the Mechanical Layer). Also, the components did not array and I didn't know if I needed to array them manually or if it was "understood" that the components in the upper left sub panel would be replicated across the other blank sub panels.

I would very much appreciate any guidance on what I may have missed along the way, why this won't work, or what I need to fix! I plan to have JLCPCB assemble the board along with the smd CCR.

Shared file:
https://easyeda.com/ElliotFan/board-mounted-al5809-15p1-7_copy

#General Discuss#
Others
Issues: UI with graphics tablet + offline logins

I'm a new EasyEDA user, also new to PCB design software, but I'm massively impressed by the software overall.  However I use a graphics tablet instead of a mouse (I'm an artist and stopped using mice decades ago), and some parts of the UI are really annoying to use with it:

The big issue is that graphics tablet pens do not click as precisely as mice - often on the down clicks, once the pen is lowered to the tablet and then removed (left-clicks are usually made with the pen tip), there is a little unintentional x/y coordinate movement.  Graphics tablet aware programs like Photoshop have tuned for these click inaccuracies, making them a joy to use.  But mouse-centric applications like EasyEDA make a mess off it - you end up constantly accidentally moving selected items when you don't mean too.

The solution is to allow a small 'dead zone', where object/node movement is not engaged after a click unless the mouse cursor moves more than a few pixels away from the click position (ideally this should be configurable).  This takes the slight pen click movement into account.

Another issue (made worse by the click movement) is selecting nodes of wires\, solid regions\, copper fill areas etc.  Clicks on these nodes have to be super-precise\, else you end up moving the entire shape rather than just the node you clicked on.  This happen to me _all the time_\, eg. I'm constantly accidentally moving copper fill areas around when I just wanted to move a node and missed clicking it by 1 pixel.  Again\, please make a wider 'hit area' for nodes so they are more easily selected.

General UI: please indicate locked objects with a different colour, or another visual effect.  Right now it is confusing when you cannot move an item, but have forgotten it was locked.

PCB view snapping seems broken:  often, nodes of objects snap to one spacing, then when selecting and dragging them again, they snap to a slightly different spacing.  As a result it's hard to get truly square regions, as each node often snaps to a different spacing than the others (repeated selection/dragging usually works, but not always).

Finally, non-UI: logins with email/password are never saved in hybrid offline mode.  Worse, old-school captchas (select matching pics) are often popped up, which is super-annoying for offline mode.  Please remember logins, and remove captchas (or at least update them to the new version, which is mostly automatic and does not require image selection).

#Bug Reports#
Bug Reports
Show part Library by clicking on any symbol in a Schematic or a footprint in a PCB.

There is no direct way to uniquely identify where in the Library a symbol in a Schematic or a footprint in a PCB comes from once it is placed in a Schematic or PCB.

There are indirect ways (described below) but a way to just click on a symbol or footprint and select an option like: "Show part in Library" would be nice.

The recommended route for creating a PCB is to start by creating the schematic first, selecting the symbols from the LCSC (for self or 3rd party assembly) or JLCPCB Assembled (for the JLCPCB PCBA service) libraries. This ensures that all the part attributes for all symbols are populated. Then it is possible to uniquely identify each part in the EasyEDA SHIFT+F library search tool just using the LCSC part number. The supplier attribute, LCSC or JLCPCB, then identifies which library the symbol came from.

If you use symbols from the System library then it is up to you to check and, if necessary, edit or populate the symbol attributes and to note somewhere (such as by adding a custom attribute) some form of unique identification of from where the symbol originated. Similar rules apply to symbols for User Contributed parts.

It is not recommended to try to identify footprints on a per part basis since one footprint may be used by many different symbols to many different parts.

One way that helps keep track of symbols (and footprints) is, before placing the first instance of any symbol, to right-click the symbol in the library then do Add Favorite. You can then find them again in your Personal Workspace > Libraries > Favorite.

#Feature Requests#
Feature Requests