Hi everyone,
this is my first post in this forum. I wanted to ask you opinions regarding my first PCB. I need opinions for everything from the layout of the PCB to the wiring diagram.
I am at the beginning of my electronic experience, so any subject is welcome.
This is the link of my project:
https://easyeda.com/gianluca.ilengo/esp8266_dht11
the final version of PCB is named: NEW_PCB4.
Thank you!
Gianluca
#PCB#Good afternoon. I'm trying to learn how to simulate using EasyEDA, however, I'm getting the "no such vector" error and I can't fix it. Thank you
The circuit:
https://easyeda.com/editor#id=ca399b9b5bfd4b68ba99a79cfb7b38dd
Log:
Circuit: gooduntitled
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000
Warning: vfonte: no DC value, transient time 0 value used
Warning: singular matrix: check nodes volprobe9 and volprobe9
Note: Starting dynamic gmin stepping
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Further gmin increment
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: Last gmin step failed
Warning: singular matrix: check nodes volprobe9 and volprobe9
Warning: Dynamic gmin stepping failed
Note: Starting source stepping
Warning: singular matrix: check nodes volprobe9 and volprobe9
Warning: singular matrix: check nodes vfonte_2 and vfonte_2
Warning: gmin step failed
Warning: source stepping failed
Transient solution failed -
Last Node Voltages
------------------
Node Last Voltage Previous Iter
---- ------------ -------------
volprobe7 0 0
vfonte_2 0 0
volprobe9 0 0
volprobe8 0 0
vfonte#branch 0 0
doAnalyses: iteration limit reached
tran simulation(s) aborted
Error(parse.c--checkvalid): volprobe7: no such vector.
ngspice-26 done
Hello guys , sorry for my dumb question ...
https://easyeda.com/editor#id=|81849bda2c7343c3901c17d790f5a619
Why my simulation doesn't work?
Circuit: gooduntitled
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000
Warning: singular matrix: check nodes r1_2 and r1_2
Note: Starting dynamic gmin stepping
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Warning: singular matrix: check nodes r1_2 and r1_2Warning: Dynamic gmin stepping failed
Note: Starting source stepping
Warning: singular matrix: check nodes r1_2 and r1_2Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful source step
Warning: singular matrix: check nodes r1_2 and r1_2Warning: singular matrix: check nodes r1_2 and r1_2
Warning: source stepping failed
Transient solution failed -
Last Node Voltages
------------------Node Last Voltage Previous Iter
---- ------------ -------------
r1_2 0 0
volprobe 0 0
v1#branch 0 0
doAnalyses: iteration limit reached
tran simulation(s) aborted
Error(parse.c--checkvalid): volprobe: no such vector.
ngspice-26 done
I need only to check a voltage with the probe. I'm trying to read the voltage probe documentation but without success.
Thanks
I cannot find out how to create a subpart. I have followed the tutorial https://docs.easyeda.com/en/SchematicLib/SchLib-Create/ word for word but each time when I right click the component in the library, the "Add Subpart" is greyed out. Can I get help on this?
Thanks,
Michael
Greetings.
I am a complete beginner in PCB design and this is my first design (making a low power ESP-12S/TPL5111 sensor) so might miss something simple when it comes to battery clips. I want to use a keystone SMD AAA battery holder (model 55). Cant use a through hole since there is enclosure stands under the PCB on that side that the pcb needs to rest upon.
In the datasheet for the clips the mounting pad layout is exactly the same dimensions as the actual battery holder pads which seems odd. I cant find when "googling" how much "extra pad" I shall have on all sides to get at good solder joint. I will most likely hand solder it, but might try hot air. Is there any rule of thumbs like X times the thickness of the plate or something?
Best regards, A
#PCB#Greetings,
I am new to SPICE and am having trouble simulating a Vishay p-channel MOSFET, specifically the SI2301CDS-T1-GE3. Surely a newbie mistake is lurking, but after many hours I've simply gotten nowhere.
Here's the project: https://easyeda.com/editor#id=0a3c7fa5ab2a41feb38417d59526aa9e
I believe the simulation is simple: I expect volProbe to report 3.3V since gate is open and source is VCC.
When running "Simulate this sheet" the system kicks back the dialog "The schematic is showing errors, please check simulation report carefully!", however the Simulation Results dialog is empty! As far I as I know (I am new at this) the netlist looks OK.
Here's what I've done, using EasyEDA SPICE docs:
I downloaded the SPICE model from Vishay https://www.vishay.com/product?docid=68741
I added the SPICE model (a .SUBCKT) with Text element and changed Text Type to SPICE
Using LCSC component "SI2301CDS-T1-GE3",
- Renamed the component to 'Si2301CDS' (match .SUBCKT)
- Changed SPICE prefix to 'X' (modeled with .SUBCKT)
- Changed SPICE pin order D=3\,G=1\,S=2 to match .SUBCKT D G S where D=1\,G=2\,S=3
Thanks for any tips!
#Simulation#Hi,
could you please support get the simulation working? I can't understand why I get a simulation error as soon as I start the simulation itself. My test model is the following: https://easyeda.com/editor#id=bf30d078cfc948bdb84ff4fa338e328c
In case you are not able to enter in the link, the model is very simple and is colled TEst
Thanks for helping!!
Regards
Mirco




