My First PCB - No Confidence!

Hello to all. I am a complete newbie here and am new to electronics in general. Trying to learn bits as I go along on an as need basis.

Attached is my first attempt at producing a PCB but I have zero confidence to get it actually made. (not sure if this is how I am supposed to link to my project????)

https://easyeda.com/editor#id=a6d22732ae7b462187fd9cdcc24be726|8f33ef781b084f03935fb56ab0d88a68

Things of concern;

  1. When this is manufactured, will the holes be made for each component based on what I have or do I need to use the 'hole' function on every component hole?
  2. For some reasons teh voltage regulator outline has been automatically created in yellow (I have assumed that teh yellow is what gets printed onto the final board). I only want to put a square around the 3 VR holes and label them something like 'In Gnd Out' and delete the pretty VR shape. I cannot work out how! Heeelp :)
  3. Are there any glaring issues?

I originally developed the circuit using another program that allowed me to do a simulation. I then progressed to using a breadboard and doing real tests that seemed to work fine and now I am moving onto PCB production. I am therefore reasonably happy that the underlying circuit is OK but am hesitating pressing teh go button an manufacture.

As some background for anybody interested, my major project is developing a data-logging system for my race car. A sub-project of that is developing some Arduino magic to calculate engine RPM. I already have an induction sensor mounted that I need to use (yes Hall Effect would be much easier). I decided it would be easier to use a digital signal rather than an analogue one. The sine wave from the sensor can read up to +/-50v at redline which the Arduino definitely wouldn't like anyway. I am learning a heap but my head is spinning!!!!!!

#PCB#
Circuit Design
Netlist will not show any IC components

I've been trying to create very simple schematics -- I've tried many different opamps etc. but the opamps never appear in my netlist. Of course, the simulation does not work properly either. It also does not load the model for the component.

I made the schematic public "hpf" in my project files
https://easyeda.com/editor#id=28c93db574d04490b889887a5aaf0457

I've gone into the examples and tried them as well. I managed to get the colpitts oscillator to show up in the netlist and simulate properly. I then loaded that same component into a schematic for a simple filter and it again gave me the same problem.

I thought EasyEDA would be a step up for me, but I'm finding this very frustrating. I've watched the videos, read the manual..... Can't figure it out. I've spent way too many hours on this simple problem and I'm about to give up and just go back to LTSpice and a separate layout package. I don't want to though!

Can anyone help?

Dave

#Simulation#
Circuit Design
My first simulation is not working

Hi, i tried build a 555 timer, run the simulation, the result:

Circuit: gooduntitled

Doing analysis at TEMP = 27.000000 and TNOM = 27.000000

Warning: singular matrix: check nodes volprobe1 and volprobe1

Note: Starting dynamic gmin stepping
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Warning: singular matrix: check nodes u1_3 and u1_3

Warning: Dynamic gmin stepping failed
Note: Starting source stepping
Warning: singular matrix: check nodes u1_3 and u1_3

Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful source step
Warning: singular matrix: check nodes u1_3 and u1_3

Warning: singular matrix: check nodes u1_3 and u1_3

Warning: source stepping failed

Transient solution failed -

Last Node Voltages

Node Last Voltage Previous Iter


xr3_1 -1.53627e-37 0
d2_1 -1.02655e-37 0
xr3_3 -2.01284e-39 0
v1_1 0 0
u1_3 0 0
volprobe1 0 0
r2_1 -1.54646e-37 -5.59605e-38
gnd 0 0
d1_1 1.00627e-30 5.59605e-38
u1_5 0 0
led1#branch 0 0
v1#branch -2.01284e-42 0

doAnalyses: iteration limit reached

tran simulation(s) aborted
Error(parse.c--checkvalid): volprobe1: no such vector.
ngspice-26 done

#Simulation#
Circuit Design