Can no longer place netlabel on GND net (allowed in V1.9.1 but not in V2.1.1)

V2.1.1 does not allow placing netlabel on GND net.

Why is this a problem?

V1.9.1 allows placing a netlabel on the GND net.

Like this:

https://easyeda.com/editor#id=80AyvtrNn

V2.1.1 does not.

So to do what the first schematic shows in V2.1.1 we now have to do it like this:

http://sandbox.easyeda.com/editor#id=h3s2ecaw5

This makes setting up the supplies for new logic devices when using hidden pins more complicated (but maybe it is more clear to the user this way?).

#Bug Reports#
Bug Reports
Edit prefix problem still present in Sandbox V2.1.1.

The text in-place prefix edit problem described in:

http://sandbox.easyeda.com/bbs_view_2048.htm

still occurs after I try to enter a prefix that has already been used in the schematic, even if the number is no longer in the schematic.

Example:

i) Place two voltage sources V1 and V2 in a schematic.

ii) Edit V1' toV3`.

That works OK.

iii) Edit V3' back toV1`: the Prefix Conflict window pops up and says that the prefix I have chosen already exists.

iv) The prefix is now showing V4.

After that, I can only enter a prefix with a number greater than any I have already entered, even if no device with that prefix number exists in the circuit. It looks like a problem with the list of refoxes entered and used in the schematic.

If I edit V4' toVpsu, and then editVpsutoV4then the Prefix Conflict window pops up and says that the prefix I have chosen already exists and the prefix becomesV5`.

But if I then edit V5' back toVpsu`, then that works OK.

#Bug Reports#
Bug Reports
Get "Simulation too large" warning but I don't think that is the problem.

BUG

I'm hoping you can help me with a problem I'm having running a netlist.

It is for a UC384x series SMPS converter, converted from LTspice to ngspice.

http://sandbox.easyeda.com/editor#id=BHFfAy864

Running it, I get the "Simulation too large" warning but I don't think that is the problem.

I have tried to run it in ngspice.com:

http://www.ngspice.com/index.php?public_circuit=4P00Ya

but that fails and gives me this error:

"Can't use .control statements with ngspice.com."

The problem there is that there are no .control statements in the copy that I have posted onto ngspice.com.

I cannot spot anything that might be misinterpreted as a .control class of statement.

This is why I think the problem may not be just because EasyEDA thinks the simulation is too large: I think there is something about the syntax that is wrong but I cannot see it and am not getting enough debug information to get any further.

Here are the things I have done to try to debug the error:

*I've put the whole netlist into different text editors to see if there are any hidden or mistranslated characters and found nothing.

*I have tested the stuff in here:

********************************************************
* Quiescent current drain
********************************************************
Bqui1 vp 0 I=V(vcc_bad)*V(vp) / 30k + (1-V(vcc_bad))*V(vp) / 1.36k
********************************************************
* Supply for error amp gated with vcc_ok
********************************************************
*B2 0 ampvcc I=5 ; uncomment for amp frequency response test
B2 0 ampvcc I=5*V(vcc_ok) ; comment out for amp frequency response test
R3 ampvcc 0 1
C2 ampvcc 0 1p
********************************************************
* Uncomment the three lines below to carry out amp frequency response test
*Btest1 0 half_ref I=V(ampvcc) / 2
*Rtest1 half_ref 0 1
*Ctest1 half_ref 0 1p
*********************************************************
* SR latch, NOR gate (and Toggle flip flop for UCx844 / 5 devices only)
********************************************************
aadc1 [delcomp] [delcompd1] adc1
aadc2 [vcc_bad] [vcc_badd1] adc1
aadc3 [ref_bad] [ref_badd1] adc1
**
* SR latch (with all output states defined)
*
anorgate3 [osc_out PWM_Qp] PWM_Qn nor1
anorgate4 [delcompd1 PWM_Qn] PWM_Qp nor1
*
apullup1 pullup pullup1 ; only used for UCx844 / 5 parts
*atflop1 pullup osc_out null null null QNd1 tflop1 ; uncomment for UCx844 / 5 devices
*anorgate1 [vcc_badd1 ref_badd1 osc_out PWM_Qn QNd1] updrvd1 nor1 ; uncomment for UCx844 / 5 devices
anorgate1 [vcc_badd1 ref_badd1 osc_out PWM_Qn] updrvd1 nor1 ; comment out for UCx844 / 5 devices
*
adac1 [updrvd1] [updrv] dac1
**
* ADC bridge model
*
.model adc1 adc_bridge(in_low = 0.5 in_high = 0.5)
**
* Pullup / down models
*
.model pullup1 d_pullup(load = 1p)
**
* T Flip Flop model
*
.model tflop1 d_tff(clk_delay = 1n
*+ set_delay = default 1n (unused)
*+ reset_delay = default 1n (unused)
+ ic = 2
+ t_load = 1p
+ clk_load = 1p
+ set_load = 1p
+ reset_load = 1p
+ rise_delay = 1n
+ fall_delay = 1n)
**
* NOR gate model
*
.model nor1 d_nor(rise_delay = 1n
+ fall_delay = 1n
+ input_load = 1p)
**
* DAC bridge model
*
.model dac1 dac_bridge(out_low = 0 out_high = 1 out_undef = 0.5
+ input_load = 1p t_rise = 40n t_fall = 2n)
********************************************************

and each of the 8 subckts separately. They all work fine.

(You can try the test jigs here:

http://sandbox.easyeda.com/editor#id=lA6QK2kCw|hnTb5mEyQ|drDYkG2M8|qwqjd7pHZ|qKgasK2Wd|VJDVd7pGY|HJj2o2eAW|Ox7tPN97s|RWw6GEXxv)

*I have also taken the whole netlist and removed or commented out each of the subckts in turn but the error persists.

*I tried moving the .ends UC3843BEE statement so that the individual subckts were outside the main UC3843BEE subckt.

Url:

http://sandbox.easyeda.com/editor#id=BHFfAy864

Browser:

#Bug Reports#
Bug Reports
Circuit Design
Problems with edit schematic text in-place in Sandbox V1.11.1

Please see:

http://sandbox.easyeda.com/editor#id=BVSCAWigC

1) In V1.9.1 it is possible to edit:

V1: PULSE(0 {vcc} 100n {tedge} {tedge} 0.1u )

interchangeably either in the text in the schematic or in the Properties panel.

When editing the same thing in the text in Sandbox V1.11.1, on clicking back on the schematic canvas, the text is shortened (the spaces are stripped out) and when viewed in the Properties panel, all the parameters have been put into the Vinitial(V) field.

Editing in the Properties panel is OK.

2) Editing the number in the prefix text in user created spice symbols is broken.

Any attempt to edit this number causes it to auto-increment! Although: sometimes the number can be edited as required (if the schematic has just been reopened?). Very confusing.

Editing prefix text in EasyEDA parts (such as resistorsseems to be OK.

Please try it in the link above.

:)

#Bug Reports#
Bug Reports