asdasdasd
Unexpectedly high cost of a simple [but large] box
I just submitted a simple but fairly large [21" x 16" x 2"] slidy-lid box that I designed in easyeda for a quotation. The cheapest I could get ["9600 Resin", even though I don't want white; none of the other technologies would print the box [too big]] was $64 for ONE lid [a flat piece of plastic with no features] and $64 for ONE box. "JLC Black Resin" was $138 for one lid plus $135 for one box. And shipping for ONE PIECE was another $100 [which I could get down to just $70 by switching to UPS]. What in the world am I doing wrong? $370 total for a plastic box that could hardly be any simpler? Is JLC3DP just n ot practical for larger pieces like this? #3D#
1002 2025-03-04 06:32:13 comment 0 0 SLA (Resin)
Can JLCPCB PCBA assemble an 00105 SMD part?
I get "Request new part" whenever I try to place any 00105 capacitor. Maybe they can't be assembled? #SMT#
1002 2025-02-27 16:17:19 comment 2 0 SMT Components
Can JLCPCB PCBA assemble a QFN part that is rotated 45 degrees?
Like this: Thanks. ...R #SMT#
1002 2025-02-26 09:38:03 comment 2 0 SMT Components
What to do if LCSC stock quantity for a part is 15000 but JLCPCB is 0?
I have a board that's almost ready for PCB production by JLCPCB. During a dry run of the production process, I notice that one of my parts [C118949] is LCSC quantity = 15000 but JLCPCB quantity = 0. How can I purchase and move parts from LCSC to JLCPCB? #Others#
1002 2025-01-05 13:50:50 comment 3 0 PCB
Component pins via'ed to nets that have planeZone layers pointlessly also autoroute on a signal layer
I created a simple schematic with parts from the common library [component details unimportant]: a 2-pin connector a resistor I exported this to a 4-layer board: with this setup: [There's a bug that automatically assigns the pour on the VCC layer to net GND; I manually corrected that.] This autoroutes as expected, two tracks on the top layer: But ... I don't want to clutter the top signal layer with GND and VCC tracks. It's the whole reason that I created those inner planes. So I created blind via types in DRC: TV is top to VCC, and TG is top to GND: Then I drop vias next to the GND and VCC pins of R1, change their nets appropriately, and convert them to the appropriate blind vias. At this point, there are ratlines from R1's pads to the blind vias, as I guess I expected: Problem 1: Autorouting this to draw the two tiny tracks from R1 to the vias hangs forever [ok... until I run out of patience minutes later...]. Problem 2: If I manually route those two tracks: [note that the ratlines went away, as expected], and autoroute [i.e., to autoroute the other components that I'd also add in a real project], it finishes, but it redraws the same two now-redundant tracks across the signal layer as before, even though they are not needed [or wanted]: Why? Can I avoid this? It's why I put in the planes and vias in in the first place: to avoid hogging real estate and setting myself up for failed routing on the top layer. Thanks! ...R #PCB#
1002 2024-03-16 17:27:54 comment 9 0 Circuit Design
I MUST be missing something
Is there still no way to search for only basic parts from easyeda? I mean, actually search. Not scroll down through a thousand rows looking for them. Not sorting them to bring the basic parts together [that doesn't work]. This seems like the easiest of features to implement --- a checkbox "Search for only basic parts". But I can't find it anywhere from the "Place" search dialog, no matter what "search engine" or "class" I check. Thanks! ...R #Schematic#
1002 2024-01-24 17:30:38 comment 2 0 Circuit Design
Out of stock parts procedure
I'd like to include in my project a part listed as out of stock on LCSC [C1526133 if it matters]. What's the procedure for that? They're in stock at Digikey and a few other places. Can I include it in a project, order, e.g., 10 assembled PC boards, and arrange to have JLCPCB order the parts from somewhere else? Can I order them from somewhere else and ship them to JLCPCB to be included on my assembled board? [I read years' old answers to this, but wanted the most current answer.] Thanks! ...R #Others#
1002 2023-12-16 11:02:09 comment 2 0 PCB
Is there a way to align one component against another, leaving the other one alone?
I often need to have one object hold still while I align one or more others to the one that shouldn't move. Some CAD programs align all of the latter-selected objects to the first-selected object. Some allow you to lock one object, then align one or more unlocked objects to the locked one. But I can't get EasyEDA to do either of these, or in any other way align one object to another without moving them both. The most obvious method would be to allow aligning unlocked objects to locked ones, with only the unlocked ones moving. But I can't even describe what it does if I try to align an unlocked object to a locked one; it doesn't seem to do anything useful. Thanks! ...R BTW, I'm aware of this post, which wasn't ever resolved; I think he asked the same thing. https://easyeda.com/forum/topic/Trying-to-align-a-component-on-top-of-a-circle-circle-also-moves-1715c54c79964db29e12eaf9f644e7dc #PCB#
1002 2023-03-13 17:29:49 comment 0 0 Circuit Design
Difference between solid region of type "Board Cutout" and tracks in the Board Outline layer
If I want a small cutout inside a board, is there any difference between using a solid region of type "Board Cutout", and just drawing a like-sized rectangle with tracks in the Board Outline layer: I've always used the board outline layer for internal cuts. But I want to do it the preferred way. Thanks! ...R #PCB#
1002 2023-03-11 21:35:43 comment 0 0 Circuit Design
Does JLC 3D do clear parts?
I see two transparent parts on the advertisement that JLC 3D shows on its home screen: but I don't see a way to select a transparent or translucent resin. I'd guess SLA, but I only see white, black, and a few other options. ...R #3D/CNC#
1002 2023-02-21 09:19:44 comment 1 0 CNC Machining
How to tell the autorouter to stop routing pins that are already internally connected in the "part"?
I've seen lots of people ask more or less the same question, some even exactly my problem, but I haven't seen a solution or workaround. I'd like to make a Raspberry Pi hat. The 2x20 pin connector that connects my hat's PCB to the Pi's GPIO connector has multiple pins on the same net. They are connected internally to the Pi, and I do NOT want to connect them also externally (to avoid ground loops and other nasties; arguing about the propriety of this is no help). Specifically, for example, pin 1 and pin 17 are both on the 3.3VDC net; they are already connected inside the Pi, and I do NOT want to duplicate this circuit by connecting the pins externally. Worse, I want to route traces in the area that the autorouter insists on blocking by routing a wholly unwanted track between these two pins. I'm aware of this: https://easyeda.com/forum/topic/Not-Connected-feature-for-unconnected-pads-in-Footprints-with-multuple-same-numbered-pads-on-PCB-03f61e1a8ed342b7a5be79e0dab765e5 Has it been fixed/added? Is there a workaround that I'm missing? Thanks! ...R #PCB#
1002 2023-02-06 00:07:13 comment 7 0 Circuit Design
Double-sided assembly
I have a small board with 135 x SMT resistors on one side and 7 x 10-position thru-hole DIP switches on the other. Is there no way to pay extra and get both sides assembled? I'm not looking forward to either soldering 270 SMT pads or 70 thru-hole pins. Thanks!! ...R #PCB#
1002 2022-05-31 01:27:10 comment 5 0 PCB
Parameter exception.
From EasyEDA, I clicked Fabrication -> One-Click Order PCB. My order is uploaded to JLCPCB, but while the Gerber is automatically loading, I get several "Parameter exception." errors. Also, the PCB's size is not filled in from the order. Any ideas? #PCB#
1002 2022-05-30 09:17:15 comment 4 0 PCB
How to handle a part with two pins on the same net
I have a board with three LCSC part C95463 3.5mm TRS jacks connected in parallel (T to T to T, R to R to R, etc.): The jack is build such that T, R, and S each come out on two pins, for mechanical stability, but internally they are electrically connected together by a metal strap that spans across the top of the connector: So I don't need to connect the two "T" pins together, or the two "R" pins, or the two "S" pins. But, the way the footprint exists in the library, if I don't connect the two corresponding pins together, I get unrouted ratlines, and DRM tells me there are orphaned nets: How can I tell the software that these pins are connected internally? I would think the footprint already has this covered: Yes, I could work around, but I'm looking for the "right" way to fix this, so workaround suggestions aren't needed. Thanks! ...R #PCB#
1002 2021-05-07 06:08:13 comment 1 0 Circuit Design
EasyEDA-generated Pick & Place file is way off?
When I got to the step in the PCB and SMD assembly order process to upload BOM and PickAndPlace files, I used EasyEDA to generate them, downloaded them from there, and then re-uploaded them to JLCPCB's order page. But the "reference" visual picture of the component placement is WAY off. The comment on the picture says the engineers will correct any mistakes, so my fingers are crossed. (1) Did I do something wrong in generating the PickAndPlace file? (2) Will this problem indeed be fixed? #PCB#
1002 2021-05-03 00:49:32 comment 3 0 PCB
Will parts with JLCPCB SMD Assembly= No definitely not be assembled?
I have some through-hole headers on my board, and they have the "JLCPCB SMD" property" = No. That is good, because I do not want these parts assembled [I will ship them loose to the customer, who will add them if they want them]. Since they are thru-hole rather than SMD, and since the parts' property is what it is, is there any need to add a note to my board order like "Please do NOT assemble parts J1, J2, or J3" ? #PCB#
1002 2021-05-02 15:49:52 comment 4 0 PCB
Do I need to order LCSC parts if I add SMD assembly to my JLCPCB PCB?
If I order a PCB from JLCPCB by submitting it directly from EasyEDA, and I add the SMD assembly service, do I also need to order the LCSC parts separately, or are they included in the price of the order? Thanks. ...R #PCB#
1002 2021-05-02 15:45:13 comment 3 0 PCB
Time from finished board to shipped?
Mine's been sitting at "Waiting for Carrier to pick up" for (if I'm reading this right) 26 hours. Does anyone know about how long an order generally takes to go from packaged to shipped? Thanks! ...R #PCB#
1002 2019-08-16 06:07:38 comment 10 0 PCB
Junctions need a Locked property
Junctions don't have a Locked property. (1) They should, because I often want to prevent changes to junctions just like any component, wire, etc. (2) Because they don't, I can't Select All to change the Locked flag on an entire schematic. #Schematic#
1002 2019-06-04 09:24:42 comment 3 0 Circuit Design
Difference between Gerber sent to JLCPCB and EasyEDA
In the EasyEDA editor, my PCB looks like this: When I generate a Gerber for my PCB, the bottom looks the same using a popular online Gerber viewer. I uploaded the same board to JLCPCB last night, but now it looks like this in the order status: Did I just waste $50? #PCB#
1002 2018-12-01 08:43:46 comment 4 0 Circuit Design
Do you mount components?
I've seen a few posts from years ago asking about JLCPCB (still EasyEDA all at the time of the posts) mounting parts (mostly that LCSC sells) to PCBs that JLCPCB makes. Does that service still exist? I need to prototype 10 boards, and I cannot mount one part (the only part that LCSC does not carry [an ISSI IS31FL3733 LED driver] because of the thermal pads). (One part is through-hole, the 40-pin Raspberry Pi GPIO connector, which I can easily mount myself). If JLCPCB can source the ISSI IC (ISSI might sample 10, and if not Mouser carries them cheaply enough) and then mount all of the SMD parts, how do I get a quote for that? Thanks! ...R #PCB#
1002 2018-11-25 16:46:12 comment 5 0 PCB
Components copper and solder from parts override copper area on other side
I have a 2-sided board. If I have all layers visible, and the selection pencil on the bottom layer, components from the top side (TopLayer, TopSilk, TopPaste, and TopSolder) are still visible instead of the bottom side's ground plane copper pour in the same area. The same is true when I'm looking at the top side: that is, bottom-side components "show through" the top-side ground plane. Is this a feature or a bug? If it's a feature, can I turn it off? In other words, can I have copper pours on the currently selected side block out all layers of components from the other side? Thanks! ...R #PCB#
1002 2018-11-22 08:05:31 comment 4 0 Circuit Design
easyeda.com says failed! trying to view 3D of PCB
When I select 3D View on a PCB, I get the error "easyeda.com says failed!". Any thoughts on what I'm doing wrong? Thanks! ...R #PCB#
1002 2018-11-12 16:10:26 comment 3 0 Circuit Design
Net Port is unaware of same nets on other sheets
BUG If I have a multi-sheet project with a Net Port with the same name on multiple sheets, in the Design > Nets they show up as having no connections --- that is, they get a red (X). This should only happen if a Net Port has no corresponding (i.e., like named) Net Port on any other sheets in the project. Steps to reproduce bug: Make a 2-sheet project. Put a resistor on both sheets, connect one end of each resistor to ground, and connect the other end to a Net Port named "A". Results: They will correctly be connected on the PC Board, but Design > Nets shows them both with a red (X). Expected results: Green check. Browser: Chrome, but likely unimportant. #BugReports#
1002 2017-08-14 12:21:08 comment 6 0 Bug Reports
Have the "No Connect" flags move with their associated parts
Feature Request Brief title for your desired feature: Have the "No Connect" flags move with their associated parts How would you like the feature to work? When I move a part with pins that are marked with "No Connect" flags, the flags should move with the part. Why is this feature important to you? It's easy to forget to move the Xs, resulting in DRC errors that have to be corrected. #FeatureRequests#
1002 2017-05-22 14:01:01 comment 4 0 Feature Requests
Be able to close the "Start" tab
Brief title for your desired feature: Be able to close the "Start" tab. How would you like the feature to work? I'd like to be able to close the "Start" tab ;) Why is this feature important to you? It's not really that important. Thanks for EasyEDA! ...R #FeatureRequests#
1002 2017-05-22 10:37:37 comment 1 0 Feature Requests
Nothing changed
Open a schematic. Move a part. Then undo the move with ^Z. The modified "*" on the tab stays on. Click "Save". You get the "Nothing changed" dialog box, but the modified "*" still stays on. And you can't close the tab without getting the "Your file hasn't been saved. Would you like to save it now?" dialog. Clicking "Close" does indeed close the modified-but-not-really-modified schematic. But the modified "*" should either go away if there aren't really any changes (like Undo rolls back to the state when the last Save took place), or if you hit "Save" and get "Nothing changed". #BugReports#
1002 2017-04-16 16:54:49 comment 0 0 Bug Reports
Team management
[I've scoured the site for an answer but didn't find anything.] Can I contribute one of my personal projects to a Team that I created, or otherwise allow the members of a Team to be able to edit one of my personal projects, without granting each team member individual edit access? I see "Upgrade to Team", but I'd like to avoid giving all of my projects to the team. Thanks!! ...R #Skill#
1002 2017-04-15 03:22:55 comment 2 0 Circuit Design