some guidance regarding measuring the creepage distance between AC and DC
Hey everyone, I wanted to ask forsections on a PCB. In the attached picture, I have used the bottom silkscreen layer to draw a line representing the path I intend to measure. I then measured the distance along that line. Is this the correct way to measure the creepage distance between the AC and DC sections of a PCB? Thanks in advance for your help!
need help with creepage clearance fix this
Hey everyone, I wanted to ask for some guidance regarding measuring the creepage distance between AC and DC sections on a PCB. In the attached picture, I have used the bottom silkscreen layer to draw a line representing the path I intend to measure. I then measured the distance along that line. Is this the correct way to measure the creepage distance between the AC and DC sections of a PCB? Thanks in advance for your help! #PCB#
Need Help With This
Hello everyone, I'm facing a small issue, and I could use your help. I’ve designed modular PCBs for projects, and divided the board into sections using cutouts with a 2 mm width. My question is: can I send this design to JLCPCB, and will they manufacture the cutouts as designed? Is a 2 mm width sufficient, or do I need to make changes to my design or the process I used in EasyEDA? Thank you for your help. #PCB#
Need help with this
Hi everyone, I designed several modular PCB sections on a single board. On the top silkscreen layer, I drew two lines to mark where I intend to cut the board with a Dremel or similar tool. I’ve also placed real holes along those lines to help cut and separate the modules myself. There are no copper traces near the cutting lines, and I intend to cut along the marked lines myself. I've attached pictures of my PCB design below for you to review. Please refer to them to see the layout. Will this approach work correctly? A simple yes or no would be greatly appreciated. Thank you in advance for your time and support. #PCB#
Need Help with my project
'm building an AC LED chaser circuit using a PIC microcontroller, a 74HC595 shift register, MOC3021 optocouplers, BT137 triacs, and an HLK-PM01 module. Could you review the schematic and PCB layout and let me know if everything looks correct? To be specific, the live input trace from the AC socket is 2 mm wide, and the output live traces are 1 mm wide, since the load current is expected to be less than 0.5 amps. Also, I've connected a push button to the PIC microcontroller to change LED blinking patterns, so please check if that connection is done properly. For neutral and ground, I haven't routed separate traces. Instead, I'm using a copper pour on the bottom layer for neutral and a copper pour on the top layer for ground. There's also a small cutout below the HLK-PM01 module for safety. Is the schematic electrically correct? Does the PCB layout look suitable for fabrication? And are the trace widths, copper fills, and clearances adequate? Please point out any mistakes or safety concerns you might see before I send it for fabrication.Thank in advance and i will share images of my projuect if you need thhem i will appricate any help i can get on this #PCB#
Need help with copper fill settings
"I'm working on my project, and I noticed many of my GND nets were left unconnected. After researching, I adjusted the copper area clearance to 0.250, and now all my GND nets connect properly, even though I have eight on the top and two on the bottom for the through-hole components. My question is: Is setting the clearance to 0.250 instead of 0.254 a good practice, and would it be acceptable for JLC PCB? I appreciate any advice—thank you!" #PCB#
Need Help with making a break out board
Hi everyone, I’m encountering an issue with my board design. I have a board with 30 components that I want to break down into smaller, individual modules for prototyping. I drew a line in the middle and set it as a board cutout. In the EasyEDA 3D viewer, I can see the cutouts as intended. However, when I send the design to JLCPCB for fabrication, it only shows a single, intact board with no cutouts. Has anyone encountered this before or does anyone know how to fix this? Any help would be greatly appreciated! #PCB#
Need Help With my drone project
#Schematic#
First Drone Project Help
This is the schematic for my first drone project. Please check if the wiring and components are correct. I’ve added a battery terminal – this is where I’ll connect the battery. There’s also an on/off switch, a microcontroller boot switch, and a reset button. The maximum trace width I can use on this board is 0.300 mm, with 0.200 mm clearance. Thanks in advance for your help! #Schematic#
Foot Print Check
Here are the images of the first footprint I created. Please take a look and let me know if it's correct. #Library#
Need help with footprint editor
Hi, I’m facing an issue in the footprint editor—whenever I adjust the width, the height automatically changes to match it. I only want to adjust the width without affecting the height. #Others#
Need Help With My First Project
Here's my new project, and I'd really appreciate it if you could take a look and point out any mistakes I might have made. In summary, it's a 12-cell charger designed for 18650 batteries, with modules included for overcharge protection. Since this is my first project, I'd love to get feedback from professionals or anyone with more experience than me.Thanks In Advance #Schematic#