asdasdasd
Version control and manipulation
I have started using version control instead of making clones of projects to make minor changes or updates. The big downfall here is I can't have two versions open at one time. I often palletize with two different designs. Previously, I could just copy and paste to make the second design. Now, I can only open one version at a time. Questions: (1) How can I open two versions at one time? (2) Can I transfer (copy?) a particular version to a project at the root of my directory? (3) How can I transfer a project at my root, and make it a version of another project that is similar and may have already have several versions? Any help you can provide would be most appreciated. Bob UPDATE: Regarding the second question, you can make a clone of any version and it will end up at the root of your directory. Solves the problem but creates others. Now you have an illegitimate copy floating around. Seems to be overkill if you just want to compare versions. Question 1&3 still open. Andy?? #PCB#
Bob11746 2023-05-11 10:57:38 comment 2 0 Circuit Design
Some misc questions
Hi Andy, 1) In both the schematic and the PCB editor, when I move symbols or parts, the wires/trace disconnect and rarely follow the parts. Am I doing something wrong? Is there a setting that I am missing? 2) When looking at net errors, the +3.3V keeps popping up. Unfortunately, when I click it, it only goes to any +3.3V net, it does not go to the pad/wire location where the problem is. With a large board, and +3.3V all over the place it can be tedious to find the problem. Is there anyway I can fix this? 3) I have created two parts, it's simply a PCB solder short and open. It is better than 0.1" header and jumpers in my application. They are two hemispheres, and the "shorted" one has an additional copper shorting the two hemispheres. This way I can place either a short or a open solder pad. I solder the open to short, or cut the "copper" area to open a particular jumper. Now, in the DRCs, the open obviously works fine, but the shorted one throws DRCs. Is there any way I can disable DRC checking for the shorted version, or fix it in the part symbol or footprint? Currently, all my DRCs are of this shorted jumper. Regards, Bob #GeneralDiscuss#
Bob11746 2022-04-07 10:12:04 comment 8 0 Others
3D model import
I cannot import .obj files. I am able to import WRL, but not OBJ. The OBJ file has the MTL file with it but no parts show up in the window when I select the OBJ file. I have a few 3d model in there now, but it is not clear where in my workspace these models are stored (default directory?). Am I correct to understand that EASYEDA OBJ files are a combination of OBJ and MTL? Typical procedure: I made a folder called 3D models under EasyEDA folder in my Windows "documents" directory (Documents/EASYEDA/3D Models) I place the zip files into the top easyeda folder and unzip to the 3D folder. The OBJ and the MTL files are there. I go to "new 3D model", select he OBJ file, but nothing shows up in the parts window. I also find the parts that do import (WRL and some old OBJ) are not sized correctly. Auto brings it close, but it needs adjustment for the pins to fit in the holes properly. Where are MY symbols and footprints stored? On my computer or in the cloud? I just can't find them. I have access to them, and I have no problems making symbols or footprints and associating them together, I just can't find where they are stored. Why is this so hard??? Help!! Bob #PCB#
Bob11746 2022-03-30 01:11:39 comment 1 0 Circuit Design
Spltting schematic into more than one sheet.
I've been having much trouble with the PCB forward anytime I edit the schematic. Any change at all rips up the part from the PCB throwing it outside the board outline. The next issue in this area is the splitting of schematics. I searched the forums for an answer but the only one I found did not help. I made a brand hew schematic, with two connectors and 11 resistors in a cascade pi arrangement, with a pair of matching net labels approximately in the middle. I did a PCB forward, and laid out all the components. I then went back tot he schematic and cut and pasted the right half ( 1net label, 5 resistors & connector) onto the second page. I then did another PCB forward and it lost all of the nets. The nets were removed and then added. See below. In my more complicated schematics, it not only changed nets, but threw a whole bunch of parts outside the board outline. What is the correct procedure for splitting a schematic into two or more sheets? This ripping up of parts also extend to library updates. Unless I change the unique identifier by completely replacing the part, it should not move or rip up nets. I should be able to suck a part into the library and then change the value and push it back into the schematic without ripping a part up. It makes it difficult to update parts without messing up the PCB end. Bob #Schematic#
Bob11746 2022-03-01 09:10:49 comment 11 0 Circuit Design
Can't find schematic
I am almost finished with schematic/pcb project. I had many variants and I decided to clean up some schematic and PCB names. Not I can't link my PCB to a schematic. When I do an "import changes" within the PCB I get it can't find the schematic. How do I relink these two files? #PCB#
Bob11746 2022-02-20 13:10:24 comment 3 0 Circuit Design
Schematic part changes
How can I change a part without ripping up copper? If I swap out a resistor, just a value change, when importing to PCB, the part is place outside the PCB outline and must be re-placed. The traces may or may not be there, but regardless, this is very inconvenient. On my office (high end) PCB program, I would import the part into the library, swap the part out, then update the part on the schematic with new parameters. If I did not do this, a new unique part identifier would be generated (even if it had the same refdes) and my PCB guy would have to re-place the part. Of course, these parts had to have the same footprint and pin numbers. Is there any such thing in EasyEDA? Thanks, Bob #PCB#
Bob11746 2022-02-01 07:09:50 comment 1 0 Circuit Design
PCB Inserting nodes
Inserting node by double clicking does not work. It might work after around twenty times. Why can't you use the "insert" and "delete" keys? This is a real pain. Also would like to be able to continue trace by double clicking (or something) and continuing the track. Right now I have two choices, move the end node to the destination, and then double click twenty times to add nodes, or, delete the whole trace and start over. Very time consuming!!! Bob #BugReports#
Bob11746 2022-01-26 06:58:39 comment 2 0 Bug Reports