asdasdasd
How to correctly replace the capacitors of the 11 VDD pins with a separate rail?
I want to highlight the VDD network in the diagram so that I can see that all 11 VDD pins of the MCU are correctly connected to a separate VDD rail and that ERC does not report any errors. Can I add an additional 4.7 µF capacitor to the VDD rail? I will add an LDO with VDD output to the diagram. #Schematic#
Caster 2026-03-02 19:50:41 comment 3 0 Circuit Design
Different clearance to copper area for RF track
I would like to keep copper area clearance 0.150 mm for the PCB but need to ensure RF 50 Ohm track clearance 0.508 mm (highlighted in the picture). I will add ground vias around the RF track (width 0.157 mm) later. What is the best approach how to achieve this? #PCB#
Caster 2024-10-17 03:02:20 comment 1 0 Circuit Design
Adding ground vias around crystal in one row.
Although I know EadyEDA can add vias to copper area I need something different e.g. place vias ground fence in some distance around crystal oscillator in one row. How to achieve this? Should I use Narrowband RF System Oscillator Layout for my LoRaWAN SAMR34 transceiver? #PCB#
Caster 2024-10-16 23:49:39 comment 1 0 Circuit Design
Which 3D model to use for RF360 saw filter 5-SMD?
Which 3D model to use in 3D manager to assign 3D model to RF360 B39871B4377P810 868MHz saw filter. It should be 5-SMD probably. Although I got B39871B4377P810.stp file from mouser.com I don't know how to convert it to *.wrl to be able to import it in EasyEDA. #PCB#
Caster 2024-10-13 20:24:26 comment 3 0 Circuit Design
How to center tracks between BGA64 pins?
I am working with SAMR34 LoRaWAN transceiver which has a small BGA64 package with pitch size 0.65 mm. The space between pins is just 0.2 mm. I don't care now that JLCPCB requires for 4-Layer PCB minimum trace width 0.1 mm and trace to BGA pad spacing also 0.1 mm which I can't fulfill. For space between pins 0.2 mm is not possible to fit a trace 0.1 mm and spacing 2x 0.1 mm, I have to use spacing 0.05 mm. The problem is I am unable to draw traces in EasyEDA in the center between BGA pins and getting DRC Errors. The EasyEDA snap them to the specified spacing although I know I can disable Snap by setting it off. Is there any way for EasyEDA to center the tracks between individual pins for me or autoroute only selected BGA pins? #PCB#
Caster 2024-10-12 18:44:20 comment 2 0 Circuit Design
DRC Errors report - Incomplete Connection
Why does DRC Errors report me an Incomplete Connection error even though both GND contacts are connected by Copper Area? I use 4 layers: Top (Signal) & Copper Area 1, RG Ground (Plane), DG&PTraces (Signal) and Bottom (Signal) & Copper Area 2. Why is Copper Area manager listing 4 layers? #PCB#
Caster 2024-10-12 17:39:40 comment 2 0 Circuit Design
N-MOSFET simulation for Resistor Voltage Divider
I need to measure the car battery voltage every hour, using a resistor voltage divider that will reduce the voltage to a max of 1 V for ADC measurement using MCU. I choose the Diodec Semiconductor N-MOSFET MMFTN138K 360mA 60V SOT-23-3. I need advice, where to get its parameters, or choose a similar type, so that I can simulate the function of the resistive divider in LTspice. #Simulation#
Caster 2024-10-05 22:37:27 comment 2 0 Circuit Design
Meaning of EP vs. WP and P0.65 in 3D models
What's the meaning of the last two characters (EP vs. WP and P0.65) in 3D models: X2SON-4_L1.0-W1.0-H0.4-P0.65-BL-EP X2SON-4_L1.0-W1.0-H0.4-P0.65-BL-WP #Library#
Caster 2024-10-02 01:08:01 comment 2 0 Circuit Design
How to add 3D model to my symbol model in favorites?
How can I add 3D to symbol model in my favorite workspace? When I convert the schematic to PCB, I can easily add 3D model "BGA-64_L6.0-W6.0-R8-C8-P0.65-TL" to my symbol layout from similar component by searching EasyEDA. #Schematic#
Caster 2024-09-30 06:26:49 comment 2 0 Circuit Design
How to convert Gerber file back to schematic ?
Is there any utility which allows me to convert Gerber file from someone project to schematic to create production files for assembly at JLCPCB ? See the article "Reverse Engineering from Gerber to PCB". #GeneralDiscuss#
Caster 2022-05-29 16:55:34 comment 3 0 Others
How to align components at the same distance ?
Is there a way to automatically align selected components horizontally so that there is the same distance between them (P1 to JP1) ? I would like to set same distances between components I have in the one row without changing their vertical position. My project is here #PCB#
Caster 2021-04-23 22:08:34 comment 2 0 Circuit Design
Track Width and Clearance Warning for unknown reason
What's wrong with my PCB design? Tracks are 0.25 mm. Design Rule [mm]: Track Width: 0.25 Clearance: 0.1 Copper Area: Clearance: 0.061 (CPWG) #PCB#
Caster 2021-04-17 22:36:05 comment 3 0 Circuit Design
Problem with LDA wiring in X2SON-4 package
Have a look at the PCB. EasyEda doesn't allow me to wire two bottom pins 3 and 4 of the LDA (PTPS7A0218PDQNR). Problem in imported schema & footprint from Texas Instruments CAD model ? Project here #PCB#
Caster 2021-02-27 06:55:01 comment 1 0 Circuit Design
Smooth segment track transition from one pad to another?
How to gradually increase the track width from one pad to another to avoid VF signal loses. E.g. from 0.3 to 0.4 mm. #PCB#
Caster 2020-12-20 10:07:35 comment 2 0 Circuit Design
Micro Cat Tracker PCB design
I would appreciate any advice how to improve PCB design to achieve the highest sensitivity for the GPS signal. The design is based on S76G chip. The tracker will be sewn or encapsulated in plastic into cat collar together with two dipole wire antennas (GPS 9.04 cm, LORA 8.20 cm, lambda/2 & lambda/4 - 5%) and fine tuned by NanoVNA. I am not sure if I should include GND pads for both antennas to signal via shielding (GPS & LORA) and make separate grounds for digital, GPS and LORA signals, connected in one place only. The PCB is 27 x 12 mm four layers: VF signal/GND, VF GND, Power lines, Digital signals/GND. The CPWG is designed to 50 Ohms (189/90/100/4.05 w/space/er height [um]/er). X1 is MEMS LSE 32.768kHz oscillator, X2 TCVCXO 26MHz and U2 is LDO 1.8V Very first PCB design, see antennas: #PCB#
Caster 2020-12-19 01:50:20 comment 9 0 Circuit Design
Symbol & footprint import from Eagle has fails
I am having troubles to import symbol and footprint from ultralibrarian.com I chose 3D CAD Model and Eagle v6+ and unzipped the generated file. In EasyEda I click on File\, Open\, Eagle\, Import File and Extract Libs and selected 2020-11-29_12-43-51_Library.scr Although the file is in ASCII, I get: Unexpected error while converting. Perhaps unsupported file type or program bug. How to get the symbol and footprint of the LDO into EasyEda? Beginning of the file: # Created by Ultra Librarian Gold 8.3.277 Copyright © 1999-2018 # Frank Frank\, Accelerated Designs Grid mil; Set Wire_Bend 2; Edit 'DQN0004A.pac'; Layer 1; Smd '1' 9.8425 12.2047 -0 R0 NOCREAM (-21.0629 12.7953); Layer 1; Smd '2' 9.8425 12.2047 -0 R0 NOCREAM (-21.0629 -12.7954); Layer 1; Smd '3' 9.8425 12.2047 -0 R0 NOCREAM (21.0629 -12.7954); Layer 1; Smd '4' 9.8425 12.2047 -0 R0 NOCREAM (21.0629 12.7954); Layer 1; Smd '5' 22.8346 22.8346 -0 R45 (0 0); Layer 51; Wire 6 (21 -21) (21 21); ... #GeneralDiscuss#
Caster 2020-11-29 22:05:21 comment 1 0 Others
What spacing to GND should I set for coplanar waveguide (CPW)
50 Ohm's for recommend trace width 5.78mi for four layer 0.8 mm PCB ? #PCB#
Caster 2020-10-25 18:27:54 comment 7 0 PCB
Via Shielding
How to make via shielding around coplanar waveguide as seen in Altirum designer here. #PCB#
Caster 2020-10-24 22:41:09 comment 1 0 Circuit Design
How to separate GND plane and guard ring?
Is there a way, e.g. draw a white line in a picture below, how I can draw a separation line around GND planes to protect the area around the oscillator? #PCB#
Caster 2020-10-17 04:57:46 comment 16 0 Circuit Design
Symbol name not replaced by a value (Place)
I have created my own symbol, SMD Resistor but I am stucked on how to automaticaly replace the symbol name by its value (Custom Attribute). Although I use R? in "Pre" field, it doesn't work. Maybe the problem is with my Footprint name I have created. #GeneralDiscuss#
Caster 2020-07-22 21:25:01 comment 4 0 Others