asdasdasd
easyeda 8.11 skip net not working
Hi to all, I'm using easyeda std version and I'm having some issues with autorouter skip nets. I selected 4 nets to be skipped but when I check the Nets in the Design Manager It show error on this nets. (check image attached) I already checked for missing connections or vias but so far nothing. If the skipped nets are correct wouldn't this nets be marked as correct? Cheers Gastón #PCB#
GastonMelo 2025-08-05 20:04:52 comment 1 0 Circuit Design
easyeda combining components with different steps pcb
Hi to all, I'm designing a pcb with components with 2.54mm step and I decide to use with 1 component of 1.27mm step. This component is through hole and I know that it requieres different design rules. How do I combine this components? I'm using easyeda SDT version Could someone point to some references? Regards Gastón #PCB#
GastonMelo 2024-12-12 18:54:03 comment 15 0 Circuit Design
EasyEda 3D not working
Hi to all, Im using EasyEda on linux tumbleweed Chromim and I can't use the 3D view, all I can see is a white window and nothing more. I tried reloading the page multiple times, close the tab where I was using the CAD but is the same. Someone knows about this error or something related? Thanks Gastón #PCB#
GastonMelo 2023-03-27 05:44:00 comment 12 0 Circuit Design
DRC wide trace small pad connection
Hi to all, im routing a 1.5mm track and I have to connect a small pad of microcontroller. How can I do that so DRC no throw error? I try to use teadrops without luck. Reducing the trace wont work because the DRC. I found this old thread https://easyeda.com/forum/topic/Track-with-multiple-widths-f987a1f8242f4e89abfa7135d88194ec But special net was removed and now in this new realeased version of easyeda how can I do that? Gastón #PCB#
GastonMelo 2022-05-11 20:41:15 comment 3 0 Circuit Design
Auto Router 4 layer PCB
Hi to all, I make a 4 layer pcb with inner1=1.8VCC and inner2=1.2VCC. When I choose the Auto Router (instead of using vias to connect each component at 1.8VCC or 1.2VCC) it uses tracks to do the connections according to the DRC. Why? Why is not using the inner layers (using vias instead of tracks)? Maybe im not using some configurations? #PCB#
GastonMelo 2019-08-28 04:22:23 comment 5 0 Circuit Design
4 layer layout
Hi to all, I made a 4 layer pcb (inner1 is 1.2VCC and inner2 is 1.8VCC) the top and bottom layer are GND. How can I make the autorouter to connect by bias to this planes and skip routing in the top and bottom layers? Regards Gastón #PCB#
GastonMelo 2019-08-25 00:42:32 comment 1 0 Circuit Design
usb connector pcb clearence error
Hi to all, im using this part C145792 and I have clearence error. image below: As you can see is between pads of the usb connector. How can I solve this? Gastón #PCB#
GastonMelo 2019-03-29 23:20:06 comment 5 0 Circuit Design
clearence_error
Hi to all, im having clearence error in easyeda. How can avoid this error? I already give more clearence in the copper area manager. Tried to relocate some components. Mayeb I missing something here. Thanks #PCB#
GastonMelo 2019-01-04 06:25:16 comment 12 0 Circuit Design
clearence error
DRC clearence settings is 3.937 mil, track width is 3.94 mil If I remove the Top Layer, the topPasteMaskLayer and the topSolderMaskLayer the DRC checking shows not errors. Why? If I enable one of those 3 i got 8 error clearence (the same number as vias). Gastón #PCB#
GastonMelo 2018-12-27 05:22:18 comment 3 0 Circuit Design
4 layer board
Hi to all, im trying to make a 4 layer board (dimensions Width:57mm height:37mm) componentes : Ic lqfp128 and capacitors. I went to layers and select 4 layer board, then went to autorouter (select local autorouter -- already have the file to local route). I choose the inner layers to signal and start the autorouter. What I can see is that the autorouter doesnt use the inner layer to autoroute (working in the top and bottom layer instead). It get stuck at 90% with the inner layer poorly routed. Maybe im missing others settings. I even try with 6 layer and the autorouter still reach the 90%. Im using linux Opensuse and mozilla (and chromium) to work with easyeda. Gastón #PCB#
GastonMelo 2018-12-24 04:11:28 comment 3 0 Circuit Design