asdasdasd
internal cutouts ??
How can I accomplish more/less rectangular cutouts in a PCB? I tired a board outline INSIDE the MAIN PCB board outline, does not react to those inner board outlines. I have done, using SLOTS, but those are really NOT what I want. Thoughts ?? #PCB#
Greg Casey 2020-04-05 02:25:57 comment 0 0 Circuit Design
internal cutouts ??
How can I accomplish more/less rectangular cutouts in a PCB? I tired a board outline INSIDE the MAIN PCB board outline, does not react to those inner board outlines. I have done, using SLOTS, but those are really NOT what I want. Thoughts ?? #PCB#
Greg Casey 2020-04-05 02:25:43 comment 0 0 Circuit Design
internal cutouts ??
How can I accomplish more/less rectangular cutouts in a PCB? I tired a board outline INSIDE the MAIN PCB board outline, does not react to those inner board outlines. I have done, using SLOTS, but those are really NOT what I want. Thoughts ?? #PCB#
Greg Casey 2020-04-05 02:25:32 comment 0 0 Circuit Design
internal cutouts ??
How can I accomplish more/less rectangular cutouts in a PCB? I tired a board outline INSIDE the MAIN PCB board outline, does not react to those inner board outlines. I have done, using SLOTS, but those are really NOT what I want. Thoughts ?? #PCB#
Greg Casey 2020-04-05 01:24:58 comment 1 0 Circuit Design
Went from 4 layers in EASYEDA to 2 Layer at Gerber ?
This is PROBABLABLY a operator error but I can't figure it out. I have a small 4 layer PCB design, with plane on inner 1 and inner 2. all signals are on top and bottom. in EASYEDA, LAYER MANAGER inner1 and inner 2 are Check and type as PLANE on the LAYER and OBJECTS -- I see both, INNER1 and INNER2 When I look directly at the layers, I see the correct "thermal" connections. When I do GENERATE GERBERS- is says 4 LAYERS BUT when I get to the JLCPCB Order It initially says 4 layers then loads GERBER file goes to 2 layers If I load a stored Gerber file (of the same design) it also says 2 layers SO, some how when I generate Gerbers it is ONLY doing 2 layers !!! Why ???? #BugReports#
Greg Casey 2019-08-27 21:23:04 comment 10 0 Bug Reports
How to delete a mounting hole WAY off the PCB ???
Somehow, Introduced a mounting hole, WAY-WAY off the PCB OUTLINE area. I can't find it therefore I can't delete it. I know it exist, when I go to gerber and use gerber view, I have a npth about 50 inches above my PCB. I looked in the .json file, "dangerous -- I am not a programmer" --- I think I see it. ID gge924 is my npth hole, I can't delete. notice the Y coordinate in the .json is really small 100 where stuff in PCB oultine is in the area of 5 million. So back to my question, how do I delete it ? I could just edit the .json file, but then how do I read that back into EasyEDA ??? Thanks for any help ; #PCB#
Greg Casey 2019-04-09 02:59:21 comment 2 0 Circuit Design
Connect a SECOND plane up - Don't even now I connected the first.
So - targeting 4 layer board -- Out signal layers, in 2 are vcc and gnd. So, I declared them in them in the layer manager and defined them as 'vcc' and 'gnd' When I look at a component with vcc and gnd nets, I think I see the connection with thermals for the GND pins (through hole), on BOTH VCC and GND Has anyone else tried doing this. ? or do you manually have to tie each pin in to the net. It appears to me that it only supports a GND Plane, NOT a vcc plane ? Am I correct ? #PCB#
Greg Casey 2019-02-04 05:06:50 comment 2 0 Circuit Design