asdasdasd
Anyone recognise this component?
https://youtu.be/uSUwHh2TRRc It's a 5050 case rgb led with an IC chip. Six pins. But it appears not to be addressable. It only performs the sweeping colour pattern seen in the video. I suspect it might be found in JLCPCB or LCSC component catalogs, but I can't figure out the search terms. In the video I apply positive voltage to the right. You see the dent mark at the bottom right corner. In an ordinary 5050 rgb led array, the dent is at cathode side. I'm most sure the very same led can be found in a garden light I have. A small lamp with a solar cell and some super capacitor. At daytime the solar cell charges the capacitor. At evening, when it becomes dark, the capacitor is discharged directly through this led. #GeneralDiscuss#
Johan_Ha 2022-08-06 18:41:51 comment 1 0 Technical Discussion
Error in datasheet and in footprint
My bug report is about component C2843784, which shows the following info in the component catalog, under PCB Footprint or Symbol: Here we can already see an error. To the left we see the symbol, telling us that pins 1, 2 and 3 are cathodes. To the right, pins 1, 2 and 3 have plus signs! When we open the datasheet, we get this image: Here we see that pins 1, 2 and 3 are indeed cathodes. We also see that the MARK is at pin 1, the cathode side. In the footprint, the MARK is at pin 1, but it has a plus sign. We can draw a conclusion that something is wrong here. We are always advised to follow the datasheet. And that would be the simplest thing to do. The simlest interpretation of this is that the plus and minus signs are wrong in the footprint. But it gets worse, and this is either the same bug or a completely different bug, that's for JLCPCB, LCSC and maybe XINGLIGHT and EasyEDA to sort out. I ordered fifteen PCBs from JLCPCB, each one had three of these leds with component number C2843784. JLCPCB did the SMT assembly. When I got the boards, I noticed that the led was a completely different component. It was the type where you add voltage to any pair of anode/cathode pins and it starts to show a colour sweep pattern red-yellow-green-cyan-blue-magenta-red etc. With a help of an integrated chip inside the component. I have tried to explain this error to the after-sales support, but they haven't so far done anything to actually track down where the error has happened. As I see it, we have a few options here. When JLCPCB made the SMT work on my board, they assembled the wrong reel of components. JLCPCB used a reel with the correct product code, but the component provider (LCSC?) had made errors in labelling reels. I have tried to find the component in the catalogs, the component I actually got, with the IC chip and the sweeping colours, but haven't found it. Xinglight, which is the manufacturer, has mixed their products and product codes. Reading further in the datasheet, we can see that in the image from the datasheet above, we can see the chip (IC). We can further see that the component reel is described. Unfortunately I don't speak or read Chinese, but the components pictured in the reel in the datasheet are not 5050 components, but something smaller. That gives an impression that the datasheet is not very accurate. And that the component information from Xinglight has been wrong from the very beginning. I only know that an error has been done somewhere. I leave it to JLCPCB to track down the error, because I have no way to actually track the error further. I believe it's in everyone's interest to find the error. #BugReports#
Johan_Ha 2022-08-06 16:41:33 comment 4 0 PCB
Harmful error in datasheets and footprints
I made a design, which included an SMD RGB LED. I happened to choose the item C2843784 found on LCSC catalogs. My intention was to order the PCB with all SMT part mounted and for some reason that was the only component I found that JLCPCB accepted. I was in hurry, so I didn't dig deeper after alternative parts. The problem was that the datasheet, the schematics and the footprint didn't match each other! This is how the footprint looked like: The red arrow and the ellipse are added later to point out the error when I chatted with the customer support at JLCPCB. As you can see, the left schematics show that pin 1, 2 and 3 are cathodes. The right footprint shows plus signs at pins 1, 2 and 3. But the footprint shows the dot and the triangle mark at pin 1. All SMD RGB LEDs I have worked with have the triangle mark at the cathode side. So it was only natural to assume the error was with the plus and minus signs in the right footprint. Because there was an error somewhere! Furthermore the datasheet of the item C2843784 shows that the triangle mark is at the cathode side! My error was to rely on the customer support at JLCPCB. They said I should follow the datasheet, which showed this image: So I went and ordered my PCBs, fifteen identical PCBs, each having three of these leds. And when I got them, they were wrong! The triangle really points out the anode, not the cathode! It is my believe that the manufacturer has made an error placing the triangle mark at the anode side. The error is not that big, if all datasheets, schematics and footprint thoroughly followed that! But now the people, who made the datasheets didn't notice the unconventional (but probably not erraneous) marking and they messed up everything. And I have 15 useless PCBs. After I pointed out the error to JLCPCB (which further reported it to LCSC), the footprint has been corrected, but the datasheet still is wrong (check it yourself), at least at the time of writing this. I even got a thank letter from LCSC for pointing out the erraneous schematics/footprint combo, but at that point I had already ordered my PCBs with wrongly placed leds. And to me, their correction still looked wrong because the plus signs were still at the triangle mark side (which turned out to be the right way!) Lesson learned: Don't trust anything, as long as the datasheet, the schematics and the footprints and all pin numbering don't match each other in the component catalogs of LCSC or JLCPCB! Have them correct the info on all places before you rely your PCB design on the info. Don't trust advice from the customer chat. They do a good job! The chat at JLCPCB responds quickly and they got LCSC to correct the footprint rather quickly. But in my case, due to production schedules, it wasn't quick enough. #SMT#
Johan_Ha 2022-07-31 16:54:40 comment 14 0 SMT Components