asdasdasd
Best way to connect vias to the Ground pour
Hi there, I am designing a 2-layer PCB in EasyEDA that will have some RF input via an SMA female PCB connector. My query is how best to link the two shielding contacts on the SMA connector to the ground plane to minimise interference etc. The footprint of the socket is not yet finalised, but is basically a central pad flanked on either side by the two shielding pads, as in the image below, along with the type of connector being used and another board with the pads in place. In these two shielding pads I have placed a set of vias that I want to connect to a ground plane when that is made. What I am unsure of is whether to connect each of the vias to the Gnd net in the schematic, so lots of wiring, such that when the Ground pour is done they will be linked or, is there another way to do it that is equally effective? #PCB#
JulesP 2025-06-06 19:05:47 comment 6 0 Circuit Design
PCB Track Current Capacity
I have a query regarding the solder tracks on a PCB that I have designed (attached). Due to high pulse currents from a capacitor, of the order of 50-120A, some of the tracks on the PCB will need to be enhanced by, if possible, adding solder to a regular track of say 4-5mm width. I don’t know what the current carrying capacity of such tracks is so maybe you have some data on this for different track dimensions of standard thickness? Besides that, do you also know if the protective resin layer on the top of a PCB will melt away with the heat of a soldering iron so I can add extra solder, or if it will resist such heat and prevent me from thickening the track? Thanks, Jules #PCB#
JulesP 2021-12-08 01:19:45 comment 27 0 Circuit Design
Replicating a project without having to reposition all the PCB components
As good practice, I made a backup of my project after completing the design and PCB for what I knew would be the first version. When I decided to work on an improved version, while still keeping the original untouched for reference, I clone it and started to work on it. However, when I went to update the PCB it started the whole PCB again with all the components positioned down in the bottom right like starting anew. How can I duplicate a project and then start on changes without having to start the PCB all over again - a lot of work! Thanks #PCB#
JulesP 2021-11-17 20:32:30 comment 2 0 Circuit Design
Heat Vias and an invisible Copper Pour
Hi there, I have a query about the best way to assist heat transfer away from a MOSFET that is likely to get quite hot. The simple circuit involves an IRF6201 with its small SOIC-8 package with which I will add a heat sink on top. However, I also wish to add some vias within the area of the footprint, as can be seen in the image. My approach is to lay out a grid of 9 vias within the main IC footprint and then do a GND Copper Pour which should allow heat to flow from the underside of the chip to the large copper area. Firstly, when I did the Copper Pour I could not get it so show despite it being 'Visible' so it's hard to see the interaction with the vias. Secondly, is this the simplest way to assist heat transfer or should I add instead a Pad under the chip and put vias in that? I have read various forum posts on the topic but I end up being a little confused by all the detail. Thanks #PCB#
JulesP 2021-01-22 01:46:19 comment 29 0 Circuit Design
Top layer tracks suddenly disappeared!
Hi there, I was busily correcting DRC errors by adjusting track clearances when all of a sudden all my top layer red coloured tracks vanished. All I have showing now is like the 'Silk' layer and none of the components can be moved. It's as if something has locked the board and removed the visibility of all the top layer tracks. Can anyone suggest how to fix this? I attach an earlier version showing what it was looking like and then the current view. Thanks Julian #PCB#
JulesP 2020-11-14 22:59:27 comment 2 0 Circuit Design
Incomplete PCB Connections Errors
I have just completed a PCB design and did the circuit check before producing the Gerber files. It came up with a whole load of 'errors' based on 'incomplete connections'. I don't understand this as all the connections are as the schematic says and, in the case of the highlighted GND one, they all connect to each other and to the GND terminal at H4 in the lower left corner. What am I missing here or is this as assumed error based on a set of circuit assumptions? Thanks Jules #PCB#
JulesP 2020-07-11 17:20:20 comment 28 0 Circuit Design
Broken PCB Connections
I have just I have just received a order of some PCB and discovered a connection fault that does not make sense. The schematic (attached PCB Query 1) clearly shows a good connection between the Earth track and the Ground connection and also the emitter of the power transistor but the PCB layout shows gaps (see PCB Query 1 & 2) that have of course reproduced on the actual PCB I have received (PCB Query 4). How is this possible? Every other connection appears good just as on the schematic. My PCB is now pretty much useless! I am in the process of preparing a much more complex circuit and if I don't have trust that all the connections will be good then how can I possibly use this particular system? Any insights would be appreciated. Thanks Jules #PCB#
JulesP 2020-07-06 19:30:43 comment 5 0 Circuit Design
Manually re-routing track
Hi everyone, I'm new to PCB design so am starting with a simple Timer circuit and have drawn the schematic circuit (attached). I have then converted this to a PCB which has gone fine but, for technical reasons, I need the Emitter from the transistor Q1 (to power a motor) to connect straight to the Ground connection rather than via the more sensitive components associated with the 555 Timer chip. I have done this in the schematic with the relevant connection showing in red. However, when the PCB is generated it chooses a different (more economical?, also attached) path of Q1 - C4 which is not what I need; which is Q1-H2 bypassing various components more sensitive to motor generated transients. I'm sure this is an easy thing to do as part of refining a board but I can't see how to do it and the shortcuts and Forum so far have thrown up nothing similar. Thanks Jules #PCB#
JulesP 2020-06-19 16:34:25 comment 1 0 Circuit Design