Push & Shove Routing
You know you want to do it. :) Alternately, a track nudger we can use to tighten up traces. #FeatureRequests#
Bug: Very complex PCBs trigger misleading "Cannot connect to server" message when Save is attempted.
I have a board with a lot of components and traces. It loads and saves fine. However, if I add some more components (about 30 in this case), while the PCB loads and edits normally, when I attempt to save it, I get a "Cannot connect to server" popup. This message is misleading because the server is up and active (I can save other PCBs in other tabs). There's something about the complexity of the board (or perhaps the sheer size) that is causing the server to respond anomalously. I am able to save the JSON to a local file - it's 7.2MB long! If there is a limit, it would be nice if the error message let you know what the problem actually is. It would be nicer if the PCB editor let you know when you were getting close to the limit. If you need more information, let me know. I can probably rig up a project that demonstrates the problem (perhaps with the extra components set with Convert to PCB = No so you can just toggle them on and off). Obviously, I can't point you to a project that contains a PCB that can't be saved, because I can't save the PCB (hahahah!) Best, Robert #BugReports#
BUG: Find Similar / (Prefix Display|Display Name) / (Same|Different) / Yes does not work
Using Find Similar, the Prefix Display / Same / Yes and Prefix Display / Different / Yes options do not find any items. Prefix Display / Different / Yes and Different / No work correctly, so there is a workaround. I also did a quick check of the other Yes/No options. Display Name exhibits the same bug. HOWEVER, Locked works fine. Perhaps a type-conversion bug? Best, Robert #BugReports#
Offset > Absolute Offset... introduces conversion errors
Board units are mils. Select a bunch of objects, traces, etc. Use Offset > Absolute Offset... to move them a large distance (like 10000 mils x and y) The final position of the new objects will often have small ([removed]
RED ALERT: New "Found Duplicated Component IDs" feature is massively buggy, causes incredible pain. Cut & Paste schematics at your own peril!
Do this: Select a part of a schematic you wish to duplicate. Copy/Paste it into a different sheet. Note that component names have been adjusted appropriately in the new copy (ie: R-1 becomes R-2, if 2is the unused open R- number. Update the PCB. You will get a warning about Duplicated Component IDs. You have to let it rename them, because there's no way to see and adjust them in schematic view! Unfortunately, your PCB is now really messed up. It looks mostly OK, but now your new R-2 component has been placed where R-1 was! And the trace(s) that connected to R-1 have had their nets updated to connect to R-2! So to fix this (when you notice what happened), you not only have to move R-2 away and put R-1 back where it was before, but you need to fix the nets on all the traces! The problem seems to be: Paste is not creating new component IDs when needed. It clearly knows enough to figure out it needs to change the component name, but it's not doing the same check for ID. Duplicated Component ID repair is changing the ID of the *older* component\, not the newer one. It's doing the exact opposite of what it should be doing. #BugReports#
Bug: Copy/Cut paste can result in track with with "null" Net
Replication steps (note: these are *very* precise; changing them in any way will not demonstrate the behavior): Zoom in on a trace consisting of a single segment so you can see the net name. Select trace and copy. Paste it somewhere. iClick in Net, hit delete, hit Enter to clear the net name. The net name of the new trace disappears. Click on the new trace. THIS IS AN IMPORTANT STEP. YOU MUST DO THIS. The trace should hilight mauve and the drag dots will be visible. If it does not do so, click on it again until it does. It is only in this state that the anomaly will present itself. Copy and then immediately paste the trace. Click on the new trace. It will display a "null" net instead of an empty net. The same behavior occurs when using cut instead of copy. Note that if the trace is not selected to the mauve state, the anomaly does not occur. The cut and paste proceed correctly, and the new trace has a blank net name. Best, R #BugReports#
Cannot delete shape using API
The API documentation does not explain how to delete a shape: https://docs.easyeda.com/en/API/EasyEDA-API/index.html#Examples In fact, it says this: Delete Shapes Removing shapes by follow code Except, there is no code example! In my case, I need to delete a track. I have tried an educated guess, such as: api('deleteShape', {id:'gge13'}) I've also tried just setting the shape to have no points, as in: api('updateShape', { "shapeType": "TRACK", "jsonCache": { "gId": t2.gId, "pointArr": [] } }); The script I'm writing ought to be very handy for a lot of people. When you're designing and redesigning a board, often your tracks get subdivided. Then when you try and move things around, only part of the track moves; you have to move each subpart and delete any bits that are hanging on. The script does two things: It looks for pairs of tracks that have the same net, layer, and width, and where the start/end of one is also the start/end of the other. It combines them into a single track. Within any track, it looks for triplets of points (a,b,c) that are in line (ie: slope(a,b) == slope(b,c)) and replaces them with the pair (a,c), simplifying the track. I have it completely working except for deleting the redundant track. Much obliged for any help that can be provided. #BugReports#
Alert when document recovery version newer than saved version on launch
Had a random lockup that happened (as they always do) just a few seconds before I was going to save. This cost me 45 minutes of work -- boo! Frantic googling ensued, and I found out about the document recovery feature -- yeah! All was not lost! In fact, only 5 minutes was lost. However, the feature is not as obvious as it should be. A simple improvement would be to check when EasyEda launches whether there are any recovery files with dates newer than the saved versions on the server. If so, pop up an alert that points the user to the recovery feature. Given that stress can suppress the immune system, these days you could be helping save lives! :) #FeatureRequests#
Can't edit silkscreen of cloned part!
Cloned a part. It appears in SCH Libs under Work Space. Selected it, hit edit. I see the schematic of the part. But there is no silk-screen outline. I understand I need to switch to the silk screen layer. But there is no layers menu. It does not appear! And there is no option to make it appear. Needless to say, I am confused. Also, all of the tutorials about this are outdated and need to be updated. #BugReports#
A few feature requests
I just started using EasyEDA and have recently completed my first project. Overall I am very happy but there are a few rough edges that I ran into. I kept a journal of them and here they are: Design rules window needs way to apply rules to multiple nets at the same time. Hotkey to finish drawing a wire and start drawing a new one. Equivalent to ESC, W Permit reversal of scroll wheel direction (helpful for Mac people) Cut and Paste shortcuts don't work in dialog boxes on desktop client, you have to use the right-click menu. Shortcut to run the currently loaded script. You can't choose the path of a cloned project. You can't edit the path of a project. Hopefully some of these are actually implemented but I just couldn't find them... Best R #FeatureRequests#
Bug Reports / Feature Notes
I just started using EasyEDA and have recently completed my first project. Overall I am very happy but there are a few bugs that I ran into. I kept a journal of them and here they are: Bug: if you copy a track, set the net of the copy to blank, THEN copy/paste the new (blank-net) track, the copies don't have a blank track. They have a NULL track! Bug: If you cut/paste a schematic between pages, any component that has a name that does not end in a digit gets a "1" appended to it, even if there is no conflict. And then when you update the PCB, because of all the name changes, components get deleted and new versions get created. The name of any object should not be changed unless it causes a conflict (in which case, a warning needs to pop up before this is done!). This also happens if you copy schematics from another project into a blank project (so you can set the project path properly by creating a new project instead of cloning) It gets worse. If you create a new project, copy in the schematic from a template project, fix any of the +"1" renames, then copy in the PCB design from the template project, when you update the PCB, it deletes any component that was renamed and creates a new component, even though the names were fixed in the schematic before the PCB was created! #BugReports#
Easily Replicating segment of PCB layout?
I'm an EasyEDA newbie so please forgive me if there's an obvious answer to this that I've missed. I am designing a board that has 8 identical submodules which are then wired together to form the final layout. I've come up with a nice layout for the submodule (and figured out how to use test pins in the design so that the module has nicely defined entry points). So far, so good. The problem is: what is the easiest way to replicate the nice layout for the other 7 submodules? I have tried: 1) Creating modules. Does not work, because importing a schematic module does not automatically use the associated PCB module (but does rename the parts and nets in the schematic), and importing a PCB module does NOT rename the parts and nets, so it's useless for multiple copies of the same module. And with no documentation that I can find, it's unclear to me exactly what the point of importing PCB modules is. 2) Selecting everything, deselect the components, copy-paste to create a set of empty tracks, move the proper components and then rename all the nets in the tracks. This works, but its tedious. If there is a simple solution, I'd much appreciate a pointer to it. One thing that I did notice is that you can select all the tracks and then clear their nets all at once. Unfortunately, there doesn't seem to be a "Rebuild Nets" feature. The algorithm would seem to be straightforward: While progress is being made, for each track in the selection, if the net is blank, then if it touches something that is in a named net, set it to that net. This would effectively flood-fill the tracks with the proper net connections. It would allow you to do this workflow: 1) Copy a group of tracks and paste them. 2) Clear their net labels. 3) Drag in the correct components (which have net labels). 4) Link all the tracks to their new components. Is there perhaps a script that does this? Thanks in advance for any help you can provide! #PCB#