What are some tips for Printing and Etching a 2 Layered PCB at home?
Hello, I am a beginner with the experience of having etched just one board (2 inches x 3 inches) for a circuit I found online. And also I am just an ordinary person who worked as a computer operator all my life. Now when I am jobless (owing to the corona scenario), I am doing some hobby electronics by watching YouTube videos. Currently, after having done a CharliPlexed 4x4x4 RGB cube - wherein I used a generic PCB and lots of wires, I decided to do a PCB on my own using EasyEda desktop version. I did the schematics, but the AutoRouter always generates two layered design. Though I am trying to get it all done on a single sided board, still, I would love to try and learn more about Double Sided board. Someday, I will even etch one. The big issue is that I am unaware of how to do that. I mean, those YouTube Videos - they make things look like "very very easy". When I tried doing both sides (just the tracing or transferring the circuit and the top layer for the one I mentioned above) - things went wrong - and I could not get the Top Layer text align with the acutal circuit. As it was just one sided PCB, I could (and did) give up doing the top layer. But this will be impossible for a double sided board! As such, I would love to know some real tips and probably those will help me get educated as well. Thanks for reading this and sharing some tips for a Novice. Stay safe. #Skill#
Via or Pad
Hello all. I am not a professional or even an electronic student. I am 50+ and work as a computer operator. Currently I do not have any job (should I say thanks to Corona Virus) and so I have spent some time doing hobby electronics I find on YouTube. I am doing a PCB for the first time - my only experience - I tried etching one from the PCB layout I found on another site (about using ATMEGA328P as a standalone) and it was successful. That inspired me to try out different things. Now, I cannot do those double-sided PCBs (as I am not any professional or expert). I did a schematic for the RGB Cube 4x4x4 Matrix and it was all good after I followed instructions at https://aglick.com/charliecube.html The only problem I found that there were too many wires. So I tried doing a PCB. And this is where I am stuck. When I used EasyEda (desktop version) it generated a two layer PCB. And sadly, if I try etching it, I am certain, I will fail (not to mention that these 2-sided copper plated boards are expensive for a jobless person). So though I wanted to risk, my situation does not permit. So I am trying it out with a single layer. Above is a screenshot of my current PCB (though not complete). Please have a look at those red boxes. What I want to accomplish is - I would add some thin wire on those positions to complete the wiring. I also saw on a YouTube video that I can use the cut-wires from earlier use of resistors. As of now, I have used Via for those ends. But I am not sure if they are the right tool to use. There is also something called Pads which seem to be of a larger dimension - can make it easy for my 1mm hand drill bit. What are the differences between the two and what would be a better solution. I know (after reading) technically, neither is required, and I can just place a 1pin jumper at those ends - as I will be soldering wires. #PCB#
Printing a Circuit for PCB Etching
Hello. I am completely new to all of this and this is the third time I am trying to print one. [The earlier two that I did were single sided and it was quite simpler, but this time, it is a dual sided design and even a bigger one almost an A4 size]. So please excuse me even if my question sounds quite "novice" or "lame". I am trying to print a design/circuit layout (not even sure if this is the right word) on a glossy paper to etch a PCB at home. Problem: The design is for a dual sided PCB. I searched and read and almost everywhere it said that I need to mirror the layout before print - and this is where I fail to understand. - Which Layer(s) I need to mirror? And How - I mean\, is it when I try printing onto paper or I generate the PNG as a Mirrored one? I would really appreciate if the community could show me the right paths. #PCB#