asdasdasd
Exporting circuit as ltspice
Hi, I wish to export my circuit sheet so I can read it into my own software. I can easily write software that will manipulate it into any form I require. The trouble I have is actually exporting it. I select FILE->EXPORT NETLIST->LTSPICE FOR THIS SHEET This causes problems. My circuit has a microphone connected to a transistor amplifier connected to two wires that provide power and take signal. The first problem is lack of a signal source. An error "Current circuit doesn't has Voltage Resource or Current Resource symbol, please place it first at left side EELIB or spice library" (SIC) appears. I overcome this problem by simply searching for a voltage resource and placing it, not connecting it to anything. Then it asks for a ground, and I add a ground, again not connecting it to anything. Then it complains again at a lack of spice models but does provide a textual spice circuit which I can select. It has some extra components, and a line '.tran 10m' which just appeared. I can delete all this. Then I can delete my modifications to the sheet, including the ".tran 10m" So my issue is, and I admit it is fairly trivial, why cannot I just create a spice circuit description without having to modify my sheet? Am I doing it wrong? #Simulation#
Peterg17 2021-10-08 13:01:30 comment 7 0 Circuit Design
problem placing smd electret microphone in pcb
Hi. I am trying to place the component B4013AM423-008 (lcsc part number c233794). In the schematic, if I click on the component in design manager it indicates the pins are connected to named nets. However in the pcb, the interface refuses to wire this connection (connection 2 in the part), although the needed link in blue is indicated. I cannot understand why, or what the problem is. I replaced the component with a similar part, with the identical problem. (c233790) It has very odd pins. A concentric outer circle and an inner circle. When I start a wire on the outer circle, I just get an immediate error. The project is called micamp, and the component is "mic1". The "com" net is having the issue. #PCB#
Peterg17 2019-12-15 20:55:51 comment 10 0 Circuit Design
Assembly problem with C40940 micro-b usb connector
Hi, I used LCSC part c40940 in a PCB design and sent it to an assembler (pcbway) to make a prototype. It is a surface mounted micro-b usb female connector. The assemblers purchased the parts from LCSC (I presume), but have a problem assembling the component onto the board. Their email says: "the model does not fit the pad. The components are of the Sinking type" This is the image the assemblers have provided: It appears that the part cannot be SMT-assembled using the layout provided. This is the very second part in the category "micro-usb connectors". Can LCSC help me with a replacement part that will fit? Obviously the assemblers have already created the PCBs, so I would rather not have to have that re-done, Regards, Peter #GeneralDiscuss#
Peterg17 2018-08-13 17:40:05 comment 8 0 Others
component orientation
Hi, The orientation on component C165947 is a mirror image of what I expected when I did the design. This component is PJ-3250 in the LCSC component libraries. (connectors -> audio connectors -> PJ-3250) The template outline is what one sees when inserted on the PCB schematic. However this is a view of the actual component from the bottom! I assumed it would be inserted on the top of the board. Not only that, the actual connection is slightly off-centre, but it is off-centre over the two instead of the three pins. Very puzzling. I have 60 of these connectors, and I can mostly insert on the bottom luckily. Is this an error, or am I missing something big here? Regards, Peter #PCB#
Peterg17 2018-08-08 09:44:21 comment 2 0 Circuit Design
DRC failures with switch/connector shielding pads
Hi, My PCB has a number of USB connections and metal bodied switches, presumably connected to "pads" which can be soldered in place. The shielding in my application is fairly critical. I presume that the shield connection on a USB connector appears on the metal jacket. As an example, consider the part https://lcsc.com/product-detail/USB-Connectors_USB-A-F-900-Ordinary-buckle-Cracked-feet-Not-high-temperature_C2345.html So I make connections between pads to carry the shielding connection. However this results in DRC errors. I am happy to ignore these of course. But I thought I would ask, possibly save me a redo. Regards, Peter #PCB#
Peterg17 2018-07-31 14:00:08 comment 4 0 Circuit Design
Cables and general system implementation
Hi, My application involves a central circuit with about 30 components, and 4 shielded curly cables each with 4 wires, attaching to this central circuit. It is a very small scale project, possibly only for myself, perhaps for a few friends, at most a few dozen. I think I can create the central circuit with SMD components, from the parts here, and get it built OK. (Does easyeda do circuit assembly? Not sure from my reading.) My main problem is the cabling. If I specify 6-way 2.54mm connectors, the size of the circuit increases substantially, and I find it very hard to attach wires to the plugs. Also very time consuming. Then I thought, why not use curly shielded usb cables. Should be possible to set connectors on the central circuit. The other ends of the cables need to attach to, variously, DIN connector, 3.5mm stereo, 2.5mm stereo connectors, and another circuit. What I want is to have these cables made up for me, as I have found I am a very unreliable solderer, and these cables are used in reasonably critical communications situations. Can anybody make any suggestions about custom cabling assembly? Regards, Peter #GeneralDiscuss#
Peterg17 2018-07-24 08:35:10 comment 3 0 Others