Requesting a second set of eyes for my ATOM sensor "Hat" Circuit to PCB
While not my first board it is only my 3rd and the 2nd was a reprint of my first because I made a stupid mistake. So learning from my mistakes I thought I would ask for some extra eyes to make sure I didn't miss anything obvious. This is, I think, pretty straight forward. I have a number of Atom M5 Lites laying around and I wanted to create a nice package that would allow me to measure T&H for my Home Assistant. With that in mind I designed the PCB. I picked the Capacitor and resistor and LED based on what were "Basic" parts so hopefully I didn't make any crazy mistakes. Since the ATOM is based off of the ESP32 and that's a 3.3V logic chip I hope I'm safe in leaving off the voltage shifter. I didn't see anything on the SHT40 which indicated that it drew more than the 100mA that the 3.3V pin on the ATOM can provide. The link to my project https://oshwlab.com/quickstar77/m5sensorshield One of my concerns is if having pins connected to the GPIOs that I'm not using will cause issues. Should I attach them to ground or maybe a resistor? SHT40 ATOM Lite M5stack Capacitor Resistor LED #PCB#
How do I leave the labels but remove the parts?
Greetings Braintrust, I am building a board to break out the pins on a Teensy 4.0 to some Grove style connectors. That part is easy but the next part is where I get stuck. https://oshwlab.com/quickstar77/teensy-grove-breakout-shield When I told EasyEDA to convert to a PCB it put both the Headers AND the teensy on the board and had all sorts of collision errors. In order to get beyond this and because I don't need the Teensy to be part of the printed board I removed it. But this removed all the helpful silk screen information like the pin numbers and the orientation of the board in the headers. I'd like to retain the silk screen information without keeping the information about what holes need to be there. This is what I have now I'd like to be able to have something like this What am I missing? -Nathan #PCB#
First time order understanding panel ordering
A couple of pieces of information I think might be relevant. I'm doing a small scale project for myself, I lack the skill to do surface mount work but can handle through hole things. My intent is to use JLCPCB to print the boards and do the SMD mounting and then do the through hole stuff myself. I want a printed board rather than a perf board for compactness and reliability. I hope to 3d print an enclosure to put the PCB in. When reviewing the options for placing an order I saw a couple of options that I understood but didn't fully understand the implications. It looks like I can design a single panel and then have that created multiple times. Or I can design a single panel with sub-panels that I break apart myself. My project has a central power board, and remote connector boards. Each central board could theoretically use as many as 12 connector boards or as few as 3. When placing the order I saw an option that identified if I would be printing different layouts. Is there a method that would be less expensive/complex than another? The way I see it I could order a board that has everything on it and break apart into multiple little boards. Or I could order the minimum number(5 I think) of boards of each board. Or something in the middle. Given my desire to have all the surface mounting done by JLCPCB, and the various extra costs associated with that, which method is preferred? I could play around with it trying all the various configurations but I thought someone might know the answer off-hand. Thank you #PCB#
First PCB design, MOSFET shield for Teensy
Greetings fellow PCB enthusiasts. My project can be found at https://oshwlab.com/quickstar77/a-bunch-of-mosfet https://easyeda.com/editor#id=|bb97d55e8eb845549517a8ae0046d747|4249db11c9f44a77883ffddf7457e06e|2f5c6bc133cb48c2809af2b4e8f8a3cb It's purpose is to allow me to control simple LED lights based on a 3.3V High from a Teensy 4.0. I took a MOSFET circuit example and multiplied it by 12. Then I added RJ-45 Jacks to act as power cable to a remote LED. My questions are; Am I using the Resistors Correctly? Does a design this simple need to worry about capacitors? For those who've designed functional circuits before does anything jump out as being "wrong"? I have a functional prototype of this design but I used a different FET so I picked out this one based on its similarities to the one I was using but I might've missed a detail. Thank you -Nathan #PCB#