Problem with JLCPCB order designed with EasyEda
Hello dear peers, We love EasyEda portal and ability to get out PCBs fast. We have been used this EasyEda/JLCPCB service for a few years by now without any problems, but on a few occasions lately we did face some rather strange questions from their staff (they call them engineers) which we never been asked before. So far we had around 400+ PCB boards runs over last two years without any visible problems (well, maybe a very few). Three weeks ago we submitted yet another board (few small modification in a mounting holes sizes) which we did already ran in different versions at least 10-15 times in a resent past. To our surprise board came back completely useless because their engineer decided to convert a clear board cutout into plated slot of different size and shape - obviously our component didn't fit into this pattern. We submitted service complain, but it does not move anywhere, and their statement regarding refund coupon didn't materialize either. Moreover, service complain is unattended for few days already. We tried to contact their support though email, bur each time different person is answering, and last one said "it was probably an error in your gerbers". So, here is the thing - we have design pattern that consists of a) top layer round pad, b) matching bottom layer round pad, and c) solid region board cutout shaped as double D-hole. 10-14 board revisions were delivered without any problems with this pattern, and we already had email exchange with the a while back asking what will be better - to implement this internal to the pads cutout through solid region board cutout, or through board outline, an d their response was "either will work fine", so we settled on solid region board cutout for clarity. And everything was ok with previous orders until last one. The problem is not the money (even though it was 2mm black PCB which is way more expensive vs green 1.6mm) - the problem is that they have a hard time to admit their error and recover fast. What customer like me (with 400+ orders in last 2 years and 30K+ spent) would expect? At least a proper communication, right? What if we would order 1000pcs after being completely happy with first 10-15 test runs and some engineer would put his/her own interpretation on implementation? Our communication with support does not produce any results (it looks like different person answers each time), and person who initially responded through service complain does not communicate through this vehicle anymore. Any advice from community how to handle this situation? Forget the money - we need to hear a) a rational justification why out of 15 identical board orders with almost identical and correct gerbers one was manufactured differently or b) clear statement that it was a production error and proposed way to recover from incident. #PCB#
JLCPCB and Allegro 17.2 generated files
Hello, I have really not that complex board design that was done for us in Allegro 17.2 and generated a standard gerbers, but it fails to show it properly and give a quote through standard approach (like gerbers generated with EasyEda). gerbers zip loads normally, but nothing happens after. Any ideas? Any help? I have few other boards made with Alllegro that I would like to submit as well alomng with my EasyEda boards. #PCB#
Editor Problem
I started to see very weird behavior last two days: 1) Already submitted and valid design - when I do open it and switch from top to bottom edit mode without actually changing anything it does mark design as modified and asks to save 2) If I save it (I need it in order to do export or generate gerbers), it completely re-names my nets - for example everything marked as net GND became some bogus $XXXXX 3) Same applies to new design - complete over-writing already saved net names 4) Coordinates X.0000 and Y.0000 become something like X.0234 and Y.0456 or somethi g like that which in turn screws up all alignment(s) So, basically, editor became totally unusable for me, especially today, and probably I screwed existing designs already by saving them as been asked by editor. Am I the only one who sees this problem? Is it any way to switch to older version in order to continue? Cheers, Alex #PCB#
Copper area and vias
Hello, I have 2-layer board with rather large top and bottom copper areas that are GND net. Is it any way I can fill them with vias in order to connect one to the other without doing it manually? I created top and bottom copper areas with keeping islands - I need them to be populated with vias as well. Any ideas? #PCB#
EasyEda PCB and Lcsc parts order
I am trying to order a few parts along with PCBs - very nice option and partnership arrangement, but my order does not show up in their system, only courier options. I already noticed similar behavior a few times in a past. My order is Y15-2060703A can somebody from EDA and/or Lcsc team explain why it is not working? I did place Eda order yesterday, and trying to add parts today. Any timely help will be greatly appreciated #GeneralDiscuss#
Pads and Solder Mask question
We have PCB design where we use pads without holes, just as copper artifact - the reason is that we need exact size and location/coordinates to maintain plus some other geometrical considerations. Bottom line is that design is done, everything looks exactly as we need, but areas where these pads are turn out as exposed copper areas (as it supposed to be). Question that I have is the following - is it ANY way I can explicitly cover pad with solder mask such as it will not show as exposed copper? (our pads are not multi-layer and do not have any holes). I saw similar question posted in 2015, but answer was not clear. Any advice or instructions how one can accomplish it? Thanks a bunch for helping! #PCB#
Painted PCB
Hello, we just tried EasyEda for few prototype boards, and one of four orders (slightly different drill holes sizes and different cuts, but basically the same design, top layer, bottom layer, top soldering mask, bottom soldering mask, few vias, one rectangular cut) came PAINTED by very rough white paint on top of soldering mask (on both sides). After few emails backward/forward with certain communication problems, I've been told that gerbers Easyeda generated did specify painting on top of soldering mask (?????). a) never heard about such a thing as painting PCBs, and b)is there a "paint" option/bottom in Easyeda (maybe I pushed something by mistake)? I feel like an idiot here. Anybody experienced the same? The funny thing is that all four (4)orders were based on exactly the same basic and simple board layout, no one asked for any kind of painting. #GeneralDiscuss#