Desktop Client - Revert to older version
Hello, Is there any way to revert to an older version of the desktop client on Linux Mint ?? Or, can you install two different versions on the same computer ?? I have older versions saved off, but when I try to run EasyEDA after installing an older version, EasyEDA sends me to the download page for the latest version. Thanks !! #GeneralDiscuss#
Convert small PCB to a Footprint
Is there any way to convert a small PCB, into a Footprint ?? I basically use they same small power supply components in most of my projects and would like to add all of them as a "component". I want to be able to design a small circuit using the Schematic Editor, then lay out the PCB. After I'm done, I'll add a New Symbol, and would like to then use the PCB I designed, as the Footprint, with matching pin #'s. I see other people wanting to repeat a series of "parts". An example I saw was an 8x8 LED Matrix, already wired to a MAX7219 IC. In this case, he wanted to drop 4 of these on a PCB, without having to wire all of them up individually. Any thoughts on how to do this ?? #GeneralDiscuss#
Footprint within another footprint ?? 7-segment filament display
(I put this in the PCB forum as I don't know where a question about footprints should be) Hello, I am trying to design a generic 7-segment display, using filament LED's, so that the final product has a retro look. A single filament LED, has two pads, and an outline, and some text indicating LED polarity. I want these to be movable and rotatable as a single element. Is it possible to group all of these elements into a single footprint, as described above, that can then be added 7 times to a new footprint, to construct the overall 7-segment display ?? Thanks, Bill This is what i have so far, and every element of every segment has to be dealt with separately. I can select a group of elements and move them, but it would be way better to click a segment, and move or rotate it with the mouse. #PCB#
Ratlines reappear for already routed traces
I've had this happen several times on different boards. It seems EasyEDA gets confused, as to where there are already traces on the PCB. This seems to only happen after many edits of the schematic, and hence the PCB. I've checked the schematic carefully regards the PCB and the already placed traces are correct. The usual fix is to delete all the existing traces between the ends of the ratline, and reroute the traces. This is getting to be a real problem for me. as I edit my PCB's a lot, to get them like I want. Sure seems like a bug to me. As an example, I added a new wire between two pins of different devices, and when I updated the PCB, it shows 4 ratlines, one for the newly made connection, and 3 for existing traces that were not changed on the schematic edit. Any ideas ?? Any way to look at a list of ratlines not routed yet, and get a hint there ?? EDIT: Saving the PCB, and closing, then re-opening EasyEDA makes no difference. Also, running in local mode on Linux Mint 19. Thanks, Bill #PCB#
Multi-Pad / Different Sized Resistor Footprint
Hello, first time poster. I have an application where the wattage of a resistor, will not be known until the the device is put into service. It could be all the way from a 1/4 watt up to a 2 watt unit. I have designed a footprint with 4 holes, to accommodate these sized resistors. The inner set are for 1/4 and 1/2 watt units, and the outer holes are for 1 and 2 watt units. The issue I'm having is the 2 sets of holes, do not behave like a usual 2 holed resistor footprint, in that the Design Rule Check.throws lots of clearance errors because, I'm assuming, the 2 holes and track at each end of my footprint , don't act as one net. Pads were placed with the PCB Pad tool and the blue tracks were placed with the Track tool, while designing the footprint. Can this be done in EasyEDA ?? I have a work-around but it is really ugly. Thanks !! #PCB#