asdasdasd
Local Cloud Sync
I have a warning "Please do not close the editor without completing the upload." It shows up in the menu bar with a red cloud symbol with a lightning bolt through it. How do I fix it? I also am unable to output gerber and other files, maybe because of this? #PCB#
circuit-man 2025-04-05 01:01:27 comment 0 0 Circuit Design
Creating and Editing PCB Footprints
There is a fairly easy way to open an editor to edit a schematic symbol. However, I have found no easy way to open a PCB footprint file to edit it. No doubt it is something easy I have overlooked, but if anyone can tell me the method, that would be fantastic! I often end up making a new one because if I have closed the old file, I don't know how to re-open it. #PCB#
circuit-man 2019-12-03 04:06:28 comment 4 0 Circuit Design
Package Error
I created a symbol (4 pins sip) for a PCB connector and assigned it a pre-defined package B4B-XH-A that was in the library. When I go to update the PCB, I get Package Error. What am I doing wrong? A screen shot of the package from the library A screen shot of the symbol definition that goes with #PCB#
circuit-man 2017-04-21 02:56:08 comment 4 0 Circuit Design
Moving labels
BUG Concise problem statement: Steps to reproduce bug: Open my PCB4 file Note the position off the circuit board of J3 and J4 labels Move them onto the circuit board and save Close the file Reopen the file. Note that the labels have again moved off-board Results: The labels do not stay. But since they do show up correctly in the Gerber Viewer, I assume that this means that the problem is opening the file again. Expected results: I expected the labels to stay where I put them. Browser: Safari Version 10.1 (12603.1.30.0.34) on MacOS Sierra Version 10.12.4 (16E195). Note: I had many other labels move around, and after repeatedly moving them, they appear to be staying put. But these two labels do not. Please tell me how to share the PCB file with you so you can address this bug. #BugReports#
circuit-man 2017-04-17 06:16:48 comment 4 0 Bug Reports
PCB manufacturing question...
I have a 2-layer PCB ready to order. It has silk screen on both sides. Is there a layer of insulation over the copper before the silkscreen? Or do you screen directly on the PCB and wiring? I am guessing "Green" means the layer painted over everything except where solder goes, but just checking... :) BTW, I did hand-routing before I discovered auto-route. Sigh. But, I like my hand route better, because it has fatter lines for things that make sense (like power). Anyway, amazing system, took some work to get to know how to use it, but WOW, I am IMPRESSED! #GeneralDiscuss#
circuit-man 2017-04-14 05:08:28 comment 1 0 Others
Capacitor polarity
I am using electrolytic capacitors, and the symbol shows one side as + and the other side not. The PCB lib drawing also shows a +. However, they are opposite. In other words, the + is acting as the ground, and the ground (on the PCB lib) as the +. I have tried to fix it by changing pin numbers, but that does not seem to work. I am using package CAP-D8.0XF3.5 #PCB#
circuit-man 2017-04-08 07:57:09 comment 4 0 Circuit Design
Missing connections
I created a PCB Lib diagram of a DTMF Shield part, with pins 1-10. I also created a symbol with the same pin designations. All but one of the pins are connected to the Arduino Nano or Vcc. However, the top 2 pins, 9 and 10, are shown in the PCB layout with no blue lines to anything. I am also getting no errors. I checked to make sure that the wires were actually connected, by moving the device on the schematic to see if the wires would follow and stay connected, which they did. What am I doing wrong? #PCB#
circuit-man 2017-04-08 06:46:06 comment 7 0 Circuit Design
Annotate Problems with renumbering U devices
I have a number of "U" type items in my 3-page schematic: Some LM358 dual op amps, an Arduino Nano, a CD4066 CMOS chip (quad bilateral switch) and two SSM2167 compressors. When I run the annotate "all schematics" option, everything seems to work fine EXCEPT the "U" numbering. Several items get labeled with the same number, and several parts of the CD4066 get assigned to different chips (overlapping part numbers, again). Is this a bug? Or am I doing something wrong? #Schematic#
circuit-man 2017-04-08 06:43:17 comment 9 0 Circuit Design