asdasdasd
ESP32 Part Recommendations
I'm updating an existing design from a couple of years ago which used an ESP32-S2-WROVER-N4R2. Looking at the current set of modules available from Espressif, it looks like the S2 series, specifically the ESP32-S2-SOLO-2-N4R2 or ESP32-S2-MINI-2-N4R2, would be the best choice. Both of these seem to be widely available from e.g. Digikey, and I would guess they are popular choices for new designs. But - neither are available from JLCPCB for some reason. Previous revs of these modules ( ESP32-S2-SOLO-N4R2 and ESP32-S2-MINI-1-N4R2) are available on JLCPCB, although not in huge quantities. Is it reasonable to use the available modules, or better to wait until the newer versions become available? I'm guessing that the newer versions are pin-compatible with older revs, but don't know that for a fact. Thanks for any advice! #Others#
jalsop 2023-12-27 17:16:22 comment 1 0 PCB
ESP32 Part Recommendations
I'm updating an existing design from a couple of years ago which used an ESP32-S2-WROVER-N4R2. Looking at the current set of modules available from Espressif, it looks like the S2 series, specifically the ESP32-S2-SOLO-2-N4R2 or ESP32-S2-MINI-2-N4R2, would be the best choice. Both of these seem to be widely available from e.g. Digikey, and I would guess they are popular choices for new designs. But - neither are available from JLCPCB for some reason. Previous revs of these modules ( ESP32-S2-SOLO-N4R2 and ESP32-S2-MINI-1-N4R2) are available on JLCPCB, although not in huge quantities. Is it reasonable to use the available modules, or better to wait until the newer versions become available? I'm guessing that the newer versions are pin-compatible with older revs, but don't know that for a fact. Thanks for any advice! #Schematic#
jalsop 2023-12-27 05:20:29 comment 1 0 Circuit Design
Connector Orientation
I want to use LCSC p/n C424689 on a custom PCB. The datasheet is here: https://datasheet.lcsc.com/lcsc/2111031430_DIBO-DB128V-5-0-15P-GN-S_C424689.pdf This is a screw terminal block with 15 positions. Maybe I'm missing something obvious, but, I am unable to figure out from the datasheet which side of the connector has the openings to insert the wires. I need this component to be oriented correctly, so if anyone can help me figure it out, I would greatly appreciate it! Thanks in advance! #PCB#
jalsop 2022-12-20 01:18:22 comment 7 0 Circuit Design
Searching JLCPCB basic parts
I use the following procedure to search for basic parts: 1. Go to https://jlcpcb.com/parts 2. Select the category e.g. Resistors/Chip Resistor - Surface Mount 3. Check the "Basic Parts" option 4. Select the resistor value\, part size\, etc. 5. Click the "Apply" button If the search fails, there is no "Back Button" functionality, and I have to start the search over. It would be nice to improve this work flow, by remaining on the search screen, so that I could, for example, select a different part size. Is there a way to do this that I haven't stumbled across? Thanks! #PCB#
jalsop 2022-02-08 14:26:36 comment 3 0 PCB
Fuse/Fuse Holder recommendation
I need to find a PCB mountable fuse holder (through hole is fine), that is available through LCSC and can be installed by JLCPCB. I've looked through the parts catalog and there are a few available but unfortunately I don't know enough to choose a suitable component. The requirements are: 1. provide 1A fuse protection 2. replacement fuses should be commonly available. Any help appreciated. Thanks! #GeneralDiscuss#
jalsop 2022-02-06 04:31:25 comment 2 0 Others
Ground Plane with through-hole components
Hi, Never done a ground plane before so I would like to get feedback as to whether my approach is correct. Please refer to this very simple schematic and PCB layout: https://oshwlab.com/jalsop/ground-plane-test I did the following: 1. Positioned the through hole components 2. Routed the non-GND tracks manually, including a via and a track on the bottom layer. 3. Added a copper area assigned to GND and placed it on the bottom layer This seems to have successfully made all the GND connections. Could someone take a quick look at the PCB 3D view and advise if everything is ok. I am not totally clear on how the +5V pin on the power jack avoids being shorted to the ground plane. I'm guessing there is a small ring of copper around the pin, and then a blank area separating it from the ground plane? Its hard to tell so I would appreciate learning from others who have already done this. Thanks in advance for any feedback! #PCB#
jalsop 2022-01-22 03:11:17 comment 2 0 Circuit Design
Missing 3D model for Header 1x15?
If I place a 1x16 female header (LCSC C124409) in my schematic, it displays nicely in the 3D view. Similarly, a 1x14 female header (C52711) displays properly. But if I place a1x15 header (C124408), no 3D model shows up. Is this a bug, or am I doing something wrong? P.S. The male 1x15 header (LCSC C2894938) works fine. #PCB#
jalsop 2021-12-10 03:51:35 comment 0 0 Circuit Design
Headers to mount a NodeMCU
Apologies if this is obvious, but I've searched the forums and not found anything. My PCB will include a NodeMCU module (an ESP8666 mounted on a small PCB). It has 2 rows of 15 pins, one down each side of the module. There are footprints available for mounting the NodeMCU directly on the PCB, and they work great. I've build a few boards with that approach. In the next iteration of my design, I want to mount the NodeMCU on female headers, to avoid soldering, and so that it can be removed/replaced easily. My question is: how do I specify the female headers in the schematic/PCB layout, so that the spacing of the headers exactly matches the spacing of the NodeMCU pins? Do I have to carefully measure the NodeMCU module and lay out the header positions exactly to match, or is there a way to specify that the NodeMCU is "on headers", thus reusing the existing footprint? Thanks! #PCB#
jalsop 2021-12-09 03:04:28 comment 1 0 Circuit Design