asdasdasd
Grounding my PCB
Hi there, I have a sort of (dumb) question. But I did a copper pour for two ground planes. My board has all headers, with no components, and one XHC connector. Do I have to connect the GND pins of my headers? Or if they are through holes is that enough (sort of like a via)? here is a picture example of my board: It's kind of a should no question, I just notice that even when I auto-routed it would not connect these pins with any tracks. Project URL: https://easyeda.com/jcfor3ver/Zone-Stand It is the ZoneStand PCB Thank you! #PCB#
jcfor3ver 2019-06-06 04:14:11 comment 3 0 Circuit Design
Pathing doesn't recognize connection
Hi everyone, I am trying to connect the following track. But the tracks don't recognize the connection to each other. The track is named RST, and when I put a via and connect a top layer track to it, it doesn't recognize the connection (ie making them the same path). And it leaves a line showing that I haven't 'connected' it. Thanks for the help #PCB#
jcfor3ver 2019-06-04 07:40:29 comment 2 0 Circuit Design
Autoroute not working
Trying to use autoroute but I keep getting the error: "Network error! Please check your network and try again!" Here is my project: https://easyeda.com/editor#id=|161b1d98adff4f8ca30f665241fce613|c15fa915dafc43dab3e26d5900de0aff|4e9ad8655af5427985b97e93c0bccf29 It is the "Zonestand PCB" I am wondering if it has to do with the shape of the board. Although I cannot change this shape as it is essential to my project. #PCB#
jcfor3ver 2019-06-04 06:57:11 comment 0 0 Circuit Design
Grounding issue, already ordered pcb's
Hi everyone, I have an issue. I meant to place a via for my GND net for one part of my circuit in order to ground it. However, I already ordered my pcb's before I realized my mistake. Below are the pictures for my design. The first one shows my GND net, however the GND net on the right is not really a "ground" net, correct? Since there is no via it is not being grounded? I put question marks because I am unsure. In the second photo I placed a via on the right side GND net, however this doesn't help my cause since I already have the boards. My main question is: Is there a proper way for me to ground my right side net on the already ordered pcb? If so, how? Could I jump a wire to a piece of rubber or something? Or is my design (like in the first picture) already grounded (on the right side of my circuit). Please let me know. #PCB#
jcfor3ver 2016-10-27 23:36:00 comment 1 0 Circuit Design
DRC track2pad error (should be simple but I'm fairly new)
Hi everyone, I have two DRC errors and I can't figure out why. Could someone please let me know what it is and how to fix it, trying to order this board today. Below are the pictures of the problem. If you want me to add and share with you my project I can do that. #PCB#
jcfor3ver 2016-10-18 03:05:17 comment 2 0 Circuit Design
Is this correctly grounded?
Hi guys, when I track the following, is it correctly grounded? Some of the grounds have cutouts for them, and some like in the picture below, I just placed a track but the track looks the same as the rest of the top layer. Am I grounding this properly by adding a track? #PCB#
jcfor3ver 2016-10-16 05:00:05 comment 1 0 Circuit Design
DRC error and I don't know why (should be simple)
Hi everyone, I have two DRC errors and I can't figure out why. Could someone please let me know what it is and how to fix it, trying to order this board today. The pictures of the problem are attached. #PCB#
jcfor3ver 2016-10-16 03:50:45 comment 8 0 Circuit Design