Where to find LTSpice power sources?
I'm setting up a circuit to simulate a RLC filter. As explained here(https://docs.easyeda.com/en/Simulation/Chapter4-Introduction-to-using-a-simulator/index.html#The-ground-node-MUST-NOT-have-a-Voltage-Probe-attached-to-it), my circuit should have a power and/or a signal source. When I'm in the circuit editor, where do I find the power source so I can add them to my circuit? I can't find them in the "Commonly library". In the "Library", selecting "Search Engine = EasyEDA", "Type = Spice Symbol" and "Classes = System", I can locate a promising section named "Power Sources / Spice Sources". In it there is a VOLTAGE_SOURCE. When I place it in my circuit, the LTSpice netlist export stops complaining and works. However, when selecting this component, it shows no section "Voltage Source Settings" where I can configure the source. My question is: where do I find the nice power sources that are exemplified here: https://easyeda.com/editor#mode=sim,id=33ceeaef756d4e4d81aef87c9b9f25ea Best regards, Jean-Michel Gonet #Simulation#
Unexpected error while converting WRL file for 3D PCB Lib
Hi all, I have the WRL file (see below) that I want to import as a PCB 3D Lib: The file is correctly rendered by a standard library like x_ite The file is accepted in online validators like instantreality The file consists in a series of Shape elements, just like those we can find in the kicad-packages3D (for example this one: PinSocket_1x01_P2.54mm_Horizontal.wrl) To load it in EasyEDA I follow the procedure described in Import 3D File: New PCB 3D Lib Select units: I selected mm (all other values return the same error) Select the file (I select the one attached below) As soon as I select the file, I get the following error message: Unexpected error while converting. Perhaps unsupported file or program bug I'm ready to believe that my file contains an error, but I have no way of correcting it: Is there a way to see some log output? Is my file incorrect, of the wrong version, or am I missing some key element? Best regards, Jean-Michel #VRMLV2.0utf8# # Pin 1: Shape { appearance Appearance { material Material { diffuseColor 0.5 0.5 0.5 } } geometry Extrusion { beginCap TRUE endCap TRUE ccw TRUE convex TRUE creaseAngle 0 crossSection [ 0.00 0.30, 0.26 0.15, 0.26 -0.15, 0.00 -0.30, -0.26 -0.15, -0.26 0.15, 0.00 0.30 ] solid TRUE spine [ 0 1.75 0, -1 1.75 0, -1 1.75 -4 ] } } # Pin 2 Shape { appearance Appearance { material Material { diffuseColor 0.5 0.5 0.5 } } geometry Extrusion { beginCap TRUE endCap TRUE ccw TRUE convex TRUE creaseAngle 0 crossSection [ 0.00 0.30, 0.26 0.15, 0.26 -0.15, 0.00 -0.30, -0.26 -0.15, -0.26 0.15, 0.00 0.30 ] solid TRUE spine [ 0 -1.75 0, -1 -1.75 0, -1 -1.75 -4 ] } } # Capacitor side: Shape { appearance Appearance { material Material { diffuseColor 0.8 0.8 0.8 } textureTransform TextureTransform { scale 1 1 rotation 0 center 0 0 translation 0 0 } texture PixelTexture { image 10 10 1 255 255 255 040 040 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 255 040 255 255 255 255 255 255 255 040 040 040 255 255 255 255 repeatS TRUE repeatT TRUE } } geometry Extrusion { beginCap TRUE endCap TRUE ccw TRUE convex TRUE creaseAngle 0 crossSection [ -3.24 -2.35, -3.80 -1.24, -4.00 0.00, -3.80 1.24, ] solid TRUE spine [ 0.0 0 0, 1.1 0 0, 1.4 0 0, 1.6 0 0, 2.0 0 0, 4.0 0 0, 6.0 0 0, 8.0 0 0, 10.0 0 0, 11.5 0 0 ] scale [ 1 1, 1 1, 0.9 0.9, 0.9 0.9, 1 1, 1 1, 1 1, 1 1, 1 1, 1 1 ] } } # Capacitor Can: Shape { appearance Appearance { material Material { diffuseColor 0.2 0.2 0.2 } } geometry Extrusion { beginCap TRUE endCap TRUE ccw TRUE convex TRUE creaseAngle 0 crossSection [ 0.00 4.00, 1.24 3.80, 2.35 3.24, 3.24 2.35, 3.80 1.24, 4.00 0.00, 3.80 -1.24, 3.24 -2.35, 2.35 -3.24, 1.24 -3.80, 0.00 -4.00, -1.24 -3.80, -2.35 -3.24, -3.24 -2.35, -3.80 1.24, -3.24 2.35, -2.35 3.24, -1.24 3.80, 0.00 4.00 ] solid TRUE spine [ 0.0 0 0, 1.1 0 0, 1.4 0 0, 1.6 0 0, 2.0 0 0, 4.0 0 0, 11.5 0 0 ] scale [ 1 1, 1 1, 0.9 0.9, 0.9 0.9, 1 1, 1 1, 1 1 ] } } #PCB#
How to add a capped via to a PCB layout?
Hi all, I'm designing a new PCB layout which will be quite tight. I would like to use via in pads to simplify my design. To do this without the solder going through the hole I would use copper capped vias, also called blind vias, which now seem to be a quite common design practice. How could I do this in EasyEda? Regards, Jean-Michel Gonet EDIT: I've changed the category of the post to JLCPCB, as suggested by Andy #PCB#
How to create a Spice component with the SUBCKT model embedded?
Hi, I've designed this circuit for simulation (find the circuit here https://easyeda.com/jmgonet/high-side-pmos-driver): The simulation runs as I intended, but I had to place a big text area with the content of the .SUBCKT model in the schematics. Actually, there are two active components in the: The BC547C, which exist in the System Library an Spice Component, and I could directly use in my circuit. The IB9343, which doesn't exist. So I took the "GENERIC SPICE .SUBCKT PMOSFET SYMBOL (ENHANCEMENT)" from the System Library, then I changed the model name, and I pasted the .SUBCKT file that I downloaded from Infineon. So this is my question: How can I create a new "Spice Component" and embed the .SUBCKT model in it, so I (or anyone) can use it without further manipulation, just like the BC547C? Regards, Jean-Michel #Simulation#
How to associate the .subckt to a New Spice Symbol
Hi all, I would like to create a new schematic symbol with a model, so it can be simulated, but I'm not able to complete the task: I can see my symbol if I open Libraries and search for for IRLB3813PBF, although I'm not sure if it is visible for other people, as it appers under Personal. If I place my symbol, it comes all complete with the spice text, which is not very practical. I believe that I have to specify somewhere the spice prefix, but I can't find where. The component I want to create is the IRLB3813PBF, by Infineon: Its spice model is available here: https://www.digikey.com/product-detail/en/infineon-technologies/IRLB3813PBF/IRLB3813PBF-ND/2118485 It is packaged in a TO-220AB, which is already available in the libraries. This is what I've done so far: From the menu, I've created a New Spice Symbol. I've drawn something that looks like a MOSFET, with a circle and three pins. I've assigned the TO-220AB(TO-220-3) package. I've numbered the pins according the the PCB package I've created a new Text area, and specified in its properties that it is a spice text. I've downloaded the spice model, which is a .SUBCKT, and pasted into the Text area. For this I've double-clicked on the text to open the multi-line text editor, so as to avoid the carriage-return to collapse. I've updated the spice number of the pins according to the inputs in the spice model. I've saved the symbol and specified the manufacturer reference, the provider and a link. I've read the following tutorials: https://docs.easyeda.com/en/SchematicLib/SchLib-Create/index.html - But there is nothing very specifc about associating the spice model. It just explains about how to use the spice number in the pins. https://docs.easyeda.com/en/Simulation/Chapter1-Introduction/index.html - It emphasizes that it is quite straightforward to create a spice symbol for it within EasyEDA either by editing an existing symbol or by creating a new one from scratch, but it only provides two links about that subject, which I've followed: https://docs.easyeda.com/en/Simulation/Chapter14-Device-models/index.html - I took from there the idea that I had to paste the SUBCKT into a text of type spice, but there are not more details about the procedure when I'm creating a spice symbol https://docs.easyeda.com/en/Simulation/Chapter15-Schematic-symbols-prefixes-and-pin-numbers/index.html - Important stuff but again, nothing particular to what I'm trying to do. Any help would be greatly appreciated. Regards, Jean-Michel #Simulation#
Non-descript error when launching a simulation with 2N2222
Hi all, This is my first simulation in EasyEDA, so I expect I'm not seeing something very obvious: I have this schematic that I would like to simulate: https://easyeda.com/jmgonet/h-bridge When I launch simulation a dialog pops up and says: "Error" but with nothing else to help me find what is about. I've read the simulation tutorials, and I was careful to choose the NPN model from the System/Spice Discrete list. I chose a 2N2222, but I actually don't care much: if needed I can change to another model. I took the passive components from the EELib, as I read that those do have spice model associated. I've tried a simulation without the NPN transistor, and it ran as expected, so I guess the models for passive components are right. As soon as I add the transistor, it starts giving me the non-descript error. I've tried other transistors, but result is always that non-descript error. I've also tried to create a new project from scratch, just in case I did something wrong with configuration. I've also tried changing the simulation parameters I'm out of ideas, so if someone can help me... Best regards, Jean-Michel Gonet #Simulation#