asdasdasd
Solid region vs regular track
Hello, Is there a difference between the two at manufacturing? For example here on the picture the right is a solid region the left is a regular track. I have them double layer and connected with VIAs to increase the surface. The goal is obviously to increase the copper surface to be able to carry even more current. Also with the solid region do I need to connect it somehow to the PADs or will it be automatically merged? With the track it's obvious. Thanks #Schematic#
keky 2025-02-17 03:14:32 comment 1 0 Circuit Design
Looking for good 5V relay to switch 230V AC main
Hello, I redesegining an old projects where I used this Wemos D1 relay shield: My model is also SRD-5VDC-SL-C Rated for 10A 250VAC This is just one of the worst quality garbage I ever seen. I produced 20 of the same circuit out of that the relay failed in about 18 of them within 2 years. The relay either stucks (does not turn off even when it clicks) or does the opposite and does not turn on. I looking for either the same form factor or smaller. The requirements: Be controllable from ESP32/ESP8266 from 3.3V control pin Turn on 230V AC home appliances up to 10A Good quality and reliable Huge plus if I can order it from the LCSC store Form factor either the same as the relay board on the picture or smaller (space does matter) Thanks a lot :) #Others#
keky 2025-02-06 04:45:03 comment 6 0 Others
Looking for 20 to 5V all in one placeable Step-Down Voltage Regulator
Hello Guys, I looking for some buck converter for my project, it should take at least 20V as input and give out 5V fix 2A at least and it operates as cool as possible (doesn't heat up a lot). I found this: LM2596 This will still need some extra components, don't you have something which can be pick and placed and all in one? Thanks #Schematic#
keky 2024-07-09 04:04:10 comment 3 0 Circuit Design
Pick and place pin headers
I don't know if this is possible but on my sketch I have used some Arduino layout for example: https://easyeda.com/modules/ARDUINO-PRO-MICRO_37f84fd49e0046a2b8c6c3bacf1395e1 I would like to add female pinheaders to hold it to the board which are assembled on it at manufacturing like this: I checked the library chosing JLCPCB assembled there are similar connectors like HDR-TH_9P-P2.54-V-F-1 but if I would to use these then I would have to delete the Arduino layout and put these to where it's pins are so my question is: Isn't there an easier way you can replace them with these type of connectors still using the original library? Also I have a bunch of regular round shape holes what I just placed with "P" on the board and will serve as male pin headers like these: isn't there an easy way to replace them with these pin headers without deleting them finding something in the library and replacing them? Also 1 final question about the BOM: will everything in the BOM with JLCPCB partnumber be pick and placed on the board? I ask because I have used layouts with referring parts but I don't want all of those to be added to the final assembly just the connectors what I select, how is this works? Thanks #GeneralDiscuss#
keky 2021-10-01 14:02:11 comment 1 0 Others
Circuit path to handle 10A
In the past I had a project where the 230V paths had to handle 10A, for this I didn't have better idea than to use the biggest width fit on my schematic (5mm) and make it double sided and connected with VIAs to give a double surface area. Then at manufacturing I have used the Outer Copper Weight 2oz for max copper area. Even then when an 1100W load was connected I could feel the device getting hot and if you calculate that: I=P/U=1100W/230V=4.7A It is only half of the planned capacity so on 10A this thing couldve burn I never tried. I'm designing another DC system which has to carry max 10A@12V through some lanes. Of course I could just add additional regular copper wires between the points and it would easily handle that but then what's the point of manufacturing a board I can just protoboard it. Is there any future for the board making which can produce strong paths like this on the picture: #PCB#
keky 2021-09-05 15:16:05 comment 3 0 Circuit Design
Trace width for 10 Amps
Hello, I would need to design a board to transport 10Amps (MAX) at mains voltage 230V. I have initially defined 2mm width traces on one side for this. I have checked this with calculators such as: http://circuitcalculator.com/wordpress/2006/01/31/pcb-trace-width-calculator/ First of all what is the default THICKNESS of a standard PCB line? (since it seems this cannot be set in EasyEDA although I can do double sided traces to double up on this with VIAs) Is this calculator any valid for your site? #PCB#
keky 2019-05-13 15:58:36 comment 12 0 Circuit Design
How to link layers
Hello, If I have a simple 2 layer schematic where at certain points I want to link layer1 and layer2 can I do that somehow without placing a pad at the intersection of the 2 layers? Thank you #PCB#
keky 2017-05-11 15:46:13 comment 3 0 Circuit Design
Importing Custom Logo (Open Source Hardware)
I would like to add mini version of this logo to my boards. https://maciek134.github.io/oshw-logo-gen/ Currently as I see it's not possible other way then export the board layout out as an image and overlay the logo with an additional program like Gimp so I post it as feature request or somebody could create this logo as a library item. Thank you. #FeatureRequests#
keky 2017-05-10 21:06:54 comment 1 0 Feature Requests
Getting the printing size right
Hello, It's bothering me long enough ever since I started using easyeda that my printed boards become huge and have to fiddle around with the Width parameter to get the size just about right. Here is what I mean: I make a pcb 80mm x 75mm. In the coordinate system I put the upper low korner of the board to 0,0 so it makes it easy to see the exact size. Then I try to print out the file as image with black on white background and I got a huge image. Actually what I see on my monitor is what I will get on the printed paper exactly so there is no problem with the printer driver here. So for my projects so far I was experimenting with always using different Width parameters at the final image export and see how it scales down. For example use width 490 for a board like this and it will come out just about right, if not try 385, 495 to see if it shrinks or grows. Another problem is with this fiddling around is that it's not scaling everything down properly. For example if I put in an Arduino nano socket, couple of jumper pins and relays. It might scales most of the components down the right size (so I can print the paper out and actually place them over) but the arduino pins get shrinked so much that it becomes useless. Any solution for this? Thank you! #PCB#
keky 2017-03-30 18:34:21 comment 4 0 Circuit Design