asdasdasd
60N60 IGBT
Hi there! I am currently working on my tesla coil which is almost done. I am using the OneTesla TC design as a reference for my DRSSTC with primary feedback. The last thing which is missing are IGBTs. If you look at the OneTesla design, you will observe high frequency pulses going to the primary (feel free to see http://onetesla.com/). The primary frequency (chosen with primary capacitor and coil itself) matches the secondary resonance frequency. This already creates problem, because it is around 230kHz. This can cause problems later, because of the 340V bus and up to 300A pulses. This forces us to use IGBT, which usually can switch as fast as 200kHz maximum. There are specified IGBTs for this job, but I not interested into ISOTOP package IGBTs (or similar high power IGBT and expensive things) anyways. There is very experienced IGBT, the FGH60N60SMD out there, which seems to perform just fine up to 300kHz and can handle presented voltages and current. And that is actually, where the problem starts. There are so many variations of 60N60 IGBT out there, please help me. IXGH60N60C3D1 IGW60N60H3 FGA60N65SMD FGH60N60SMD The price really matters for me. If not, I would just simply pick the FGH version. My question thow is, if there is a difference between those, maybe, if there is better version of 60N60 IGBT than FGH (like IXN...). If there is not difference, does it mean that I just pick the cheapest one and it will work like a charm? Alse, if there is not better IGBT version of 60N60, I will take the FGH60N60SMD and we will be settled. Let me know your experience. Thanks #GeneralDiscuss#
matko123 2019-02-03 01:38:35 comment 8 0 Others
oneTesla working behavior
Hello all! I am quite a while trying to make my own DRSSTC, but i did not get any results that would make me happy. I probably made some arcs, but they were just too weak for me. But i crossed across oneTesla design of DRSSTC, which is just perfect. I want to make the driver circuit according to their design, but there is just one problem. No matter how hard i try, I have not been able to understand how it works. Feel free to have a look at the schematic of driver (http://onetesla.com//media/wysiwyg/downloads/tsschem.png) and interrupter (http://onetesla.com//media/wysiwyg/downloads/sdintschem.png). Also, feel free to have a look at oneTesla website (http://onetesla.com/), especialy at the Tutorials stage (http://onetesla.com/tutorials), where the for me the non-understandable information is. I had a look and studied datasheet of every single component, so most of the circuit is logical. I am not a beginner, so it bothers me that I cannot understand the whole working principle. I have some questions. If i will be able to answer all of them, than i can make the Tesla Coil (please, answer them as understandable as possible): - how can we do "zero crossing switching" when the negative current passes through current transformer? is not the voltage negative\, too? how we know the current is zero? - what is the behavior of 74hc74 flip-flop? The logical table seems pretty non-understandable. - why is the high-side UCC inverted? I had a look at the previous version of oneTesla TC and the MOS-drivers were flipped. So\, the phasing of the primary of the GDT does not matter? Does it means that is i build my own GDT, all I have to care about i phasing of the secondary coils? The primary does not matter? - can be the optical transmitter and receiver (IF-D95T) replaced by a optocoupler? Is the normal state of IF-D95T 5V or 0V (normal state = i mean when there is not signal from transmitter)? - can i use 200:1 current transformer instead of 300:1 (oneTesla generally uses 300:1\, but it is not available anywhere) ? - please\, describe the whole working principle of the circuit. Please\, i cannot do it by my self. Say the voltages in every stage of circuit when the circuit starts\, when there is signal from interrupter and when there is not. Thank you a lot for your answers and time. Thanks again, i do not know what shall i do without you. #GeneralDiscuss#
matko123 2019-01-01 19:01:23 comment 2 0 Others
High side mosfets
Hey all. I made a H-bridge consisting of four N mosfets and drivers IR2184 (its the same as IR2104) to drive my Tesla Coil. It worked like a charm until i blew it. I wanna to make H bridge of N mosfets without aby driver. How to control the high side mosfets efficiently? Thanks for help. #GeneralDiscuss#
matko123 2018-07-01 18:56:18 comment 2 0 Others
arduino programmer
Is it possible to programme arduino using atmega8 USB to serial converter? Here is link of my atmega8 programmer: http://www.electronics-lab.com/project/usb-to-serial-converter-using-avr-microcontroller/ Is this atmega8 programmer the same of ft232rl board? Can i use the same software? Will be in programming any different steps? Is there any different between this atmega8 programmer and ft232rl board? Can i use the same programming codes? Thank you for answers. #Schematic#
matko123 2017-06-01 02:41:53 comment 2 0 Circuit Design
Mosfets
Can i use mosfet IRLZ34N instead of mosfet IRLZ44N? Thank you for your answers. #Schematic#
matko123 2017-05-10 20:58:34 comment 8 0 Circuit Design
charger
please, can someone show me schematic of charger. i need to charge 3.7 and 100mAh LIPO battery. i have this components: LM317, DW01 and 8025. i can use some transistors, resistors, diodes and logic ics, too, but i have not got zener diode and tp4055 (or 4056, 4057 and 4058). i thank you so much for all schematics. #Schematic#
matko123 2017-03-23 21:18:47 comment 6 0 Circuit Design