How to Display Pin Numbers of LM324 Package
My schematic uses 3 out of the 4 Op Amps in the LM324 package, so I have Ux.1, Ux.2. and Ux.4 (I'm not using Ux.3). The schematic shows the 3 op amps, but with no pin numbers. How do I get the pin numbers to display in my schematic? #Schematic#
Basic 555 Astable Produces Noisy Square Waves And Then Stops Oscillating
The following basic astable 555 cirucit, which should have a period of about 2 seconds and a duty cycle of around 58%, produces a noisy square wave for about 60 seconds and then finishes the last 40 seconds of the simulation at a constant voltage: Basic Astable 555 Period=2s, Duty=58% The not-that-great-looking waveform is: Why is this not a pretty square wave? Why does it stop after 60 seconds? #Simulation#
Convergence and No Such Vector Errors Simulating Basic Astable 555
My basic astable 555 circuit: Basic Astable 555 Produces both the "Too many iterations without convergence" and the "Error(parse.c--checkvalid): square: no such vector" error. Both errors are a mystery to me, especially the no such vector error. Any help appreciated. Here's the full simulation log: Circuit: untitled Doing analysis at TEMP = 27.000000 and TNOM = 27.000000 Note: Starting dynamic gmin stepping Note: One successful gmin step Note: One successful gmin step Note: One successful gmin step Note: One successful gmin step Note: One successful gmin step Warning: Further gmin increment Note: One successful gmin step Note: One successful gmin step Warning: Further gmin increment Warning: Further gmin increment Note: One successful gmin step Note: One successful gmin step Warning: Further gmin increment Warning: Further gmin increment Warning: Further gmin increment Note: One successful gmin step Note: One successful gmin step Warning: Further gmin increment Note: One successful gmin step Warning: Further gmin increment Note: One successful gmin step Warning: Further gmin increment Warning: Further gmin increment Note: One successful gmin step Warning: Further gmin increment Note: One successful gmin step Warning: Last gmin step failed Warning: Dynamic gmin stepping failed Note: Starting source stepping Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Note: One successful source step Warning: source stepping failed Transient solution failed - Last Node Voltages ------------------ Node Last Voltage Previous Iter ---- ------------ ------------- xu1.25 0.657512 0.657513 xu1.2 1.46796 1.46818 xu1.3 1.74324 1.74324 xu1.6 1.17052 1.17052 xu1.8 1.71404 1.71404 xu1.9 1.78002 1.78002 xu1_8 1.78002 1.78003 xu1_2 0.785106 0.78469 xu1.5 0.482687 0.482452 xu1.17 0.161441 0.161441 xu1.4 0.72765 0.72765 c2_2 1.1951 1.1951 xu1.12 1.62706 1.62706 xu1.20 1.18674 1.18674 xu1.10 1.75036 1.75036 xu1.22 0.0552941 0.0557033 * xu1.11 1.16652 1.16631 xu1.14 1.02783 1.02782 xu1.13 1.08117 1.08116 xu1.18 0.610366 0.610363 xu1_7 0.78519 0.784759 xu1.15 0.466162 0.466174 xu1.31 0.616501 0.616501 xu1.27 1.07988 1.07989 xu1.24 0.0129945 0.0129943 xu1.29 1.10502 1.10501 xu1.28 0.491146 0.49113 xu1.16 0.466165 0.466178 square 0.0999989 0.0999955 xu1.26 0.466157 0.466169 v1#branch -0.000595154 -0.00059516 doAnalyses: Too many iterations without convergence tran simulation(s) aborted Error(parse.c--checkvalid): square: no such vector. ngspice-26 done #Simulation#
Cannot simulate the simplest RC circuit.
I have a circuit I'm working on and was considering adding a simple RC circuit to control a transistor to enforce an initial state. I got as far as adding the capacitor in series with a grounded resister and threw in a voltage probe between the cap and resistor to fine tune the RC value before proceeding with adding the transistor and the rest of the initial state logic. What I discovered was that the voltage between the cap and resistor is always zero no matter what values I use for the cap and resistor. I even tried a full Farad for the cap and 1 Megohm for the resistor and still the voltage on the probe was a constant zero. Could someone take a look at the circuit and see what I could have missed? You can ignore all the op amp stuff and just look at the battery, the ground, C4, R12 and the probe, volProbe1. enter link description here I was running a transient simulation, starting at time 0, the increment set to 1 second and taking the simulation out to 120 seconds. Here's an image of the circuit with the relevant RC circuit circled: And here's an image of the transient simulation with the relevant probe and output identified: #Simulation#
Run the Document > Transient Not Producing Time-Based Graph
I was testing a simple op amp based square wave generator and getting good results from Run the Document > Transient. I.e. I was getting a nice looking square wave. Then, Run the Document > Transient stopped working. Instead of producing a time-based graph, it now behaves exactly as though I had selected Simulation results... I am getting back a window with the title "Show your simulation results" contain the SPICE simulation results with the option to Download the netlist or Close the window. #Simulation#