asdasdasd
Schematic: Net name overlaps line (minor issue)
BUG Concise problem statement: Steps to reproduce bug: Draw a horizontal net line on a schematic Put a net name on it, where the name is above the line Results: The net name is right on the line Expected results: Net name is far enough above the net line to look good Browser: Firefox #BugReports#
mesopcb 2015-12-15 03:59:07 comment 7 0 Bug Reports
Autorouter duplicates existing traces
BUG Concise problem statement: My file where the autorouter has been run has each routed trace twice Steps to reproduce bug: Create a PCB by autorouting Run autorouter again with "rip up traces" NOT CHECKED Results: Each trace will exist twice. This can only be seen by deleting an existing trace and noticing that it appears to still be there (a second copy). Also, by moving a trace endpoint at an angle, the other trace can be seen. Note that the only problem with this is that an extra trace (maybe more?) shows up when modifying an autorouted board. Expected results: No excess traces Browser: Firefox 41.0.2 This can be seen in my project 'Demonstrate Bugs' which I have shared with support. This is not a critical problem, but when modifying an autorouted board, it slows things down. I have not created a simple project to replicate this, but the doubled traces are visible in the board in the project, except for the wider traces which I manually redid. It appears that the autorouter was upgraded today. I did not notice this bug before the upgrade, but I didn't do much post-autoroutde board editing before, so I don't know if this is a new bug. #BugReports#
mesopcb 2015-11-04 00:27:01 comment 5 0 Bug Reports
How to export board image as a large image.
I have a 2" x 3" board. I would like to print it on a full page on my printer. When I export it as pdf, it has a lot of unused space in the .pdf file. I have tried to reduce the PCB canvas size to the board size, but it will not go smaller than 12000 x 12000 mils. When I export as an image, it has such low resolution that if I expand the image, my small traces are highly pixelated. How do I print my PCB zoomed in? #Skill#
mesopcb 2015-10-24 03:05:46 comment 17 0 Circuit Design
Autorouter rips up solid area but routes to it
BUG Concise problem statement: Auto router rips up a solid area but routes to it. "Rip up" is not checked. Steps to reproduce bug: Create a solid area on the bottom layer and assign it a net name (I used ANGND, a common net on my board). You can use my file with "removes solid" in title. Router settings are 8,10,8,34,18. No boxes checked, not special nets. Run autorouter with "rip up nets" not checked Results: Autorouter successfully routes board, but removes the solid area even though it routed one net to it. Expected results: The same result, but with sold area still present. Browser: 41.0.2 #BugReports#
mesopcb 2015-10-23 02:08:53 comment 1 0 Bug Reports
DRC shows errors with non-conductive layers
BUG Concise problem statement: Steps to reproduce bug: 1.See shared file with "DRC wrong" in file name Results: DRC shows many errors in Design Manager where conductive errors are close to silk screen or board edge elements. Expected results: DRC only shows real errors - where conductors are too close to each other. Maybe where board edge tolerance is violated. Browser: 41.0.2 #BugReports#
mesopcb 2015-10-23 01:04:50 comment 3 0 Bug Reports
How to create a single point interconnection between two nets
On my board, I have two ground nets: GND and ANGND. I want to connect them at only one point, for noise reduction reasons. In other words, everything on GND should be connected together, everything on ANGND should be connected together, and GND and ANGND connected together only at one place How should I do that? #Schematic#
mesopcb 2015-10-18 20:24:30 comment 2 0 Circuit Design
Save As with same file name creates duplicate
BUG Concise problem statement: Steps to reproduce bug: Save a PCB file as Save As Later save another with As Results: Project now shows two PCB's with the same name Expected results: Old file overwritten with new, perhaps with choice dialog first Browser: Firefox 41.02 #BugReports#
mesopcb 2015-10-18 20:22:15 comment 1 0 Bug Reports
Autorouter rips up nets when not checked
BUG Concise problem statement: Major problem: Even when the "rip up nets" box is unchecked, the autorouter rips up all nets. Steps to reproduce bug: Work on a PCB, doing multiple autoroutes, some with "rip up nets" checked Put in some traces manually Run the autorouter with "rip up nets" not checked Results: All nets are ripped up. BUT... this didn't happen until I had been doing this for some time. Now, I cannot auto-route my board without all nets being ripped up every time. I cannot proceed with this PCB until this is fixed. Expected results: Existing nets remain, and autorouter attempts to route remaining nets. Browser: Firefox 41.0.1 (OS X) Note: Settings in autoroute box are: Ripup Nets: Unchecked Skip Net: blank Model: Real Time Special Nets: GND and ANGND - width 20mils #BugReports#
mesopcb 2015-10-13 04:23:59 comment 2 0 Bug Reports
Parts Pins Display fails for multipart part
BUG Concise problem statement: In Design Manager, the parts pins are not shown for parts of a multipart part Steps to reproduce bug: On schematic, add one piece of a multipart part (e.g. 7404) Wire up some nets to it Go to design manager, refresh everything, click on sub-part's designator. Part pins are not shown Results: Parts pins are not shown Expected results: Parts pins are shown with their nets Browser: Firefox 41.0.1 #BugReports#
mesopcb 2015-10-13 02:20:54 comment 3 0 Bug Reports
Autorouter seems to have disappeared
BUG Concise problem statement: The autorouter symbol is not present on my new project. I used it on a previous project. Version is 2.8.2 Steps to reproduce bug: Create a PCB from schematic capture, with no error messages Go to PCB Editor Results:Observe autorouter icon not present Expected results: Autorouter symbol present Browser: Firefox 41.0.1 (Note: previously I used Chrome with autorouter) #BugReports#
mesopcb 2015-10-12 01:15:05 comment 2 0 Bug Reports
Wrong reference numbers after using multi-part part
BUG Concise problem statement: I get repeat reference number assignments if I add a normal part after adding a couple of parts of a multi-part item Steps to reproduce bug: Create a multi-part schematic item. I used a 7474 Add the .1 and then the .2 sub-parts to a schematic - They will be U1.1 and U1.2 respectively Add a normal part, say a 74597 to the schematic. It will be U1 Results: The normal part has the same part reference number as the sub-parts of the other part. Expected results: The normal part will have the next reference number available. Browser: Chrome Version 45.0.2454.93 (64-bit) (Mac OS X Yosemite) #BugReports#
mesopcb 2015-09-22 00:04:55 comment 4 0 Bug Reports
How to use symbol from easyEda libs for new part symbol
I would like to be able to use the schematic symbol from the a part in the standard easyEda libs as a starting point for making a new part symbol. For example, there is a nice GND symbol. I'd like one of my own that has the name AGND and a net of AGND (for analog ground). I could draw one, but it would be nice just to start with one in the easyEda libs. I know how to get a symbol from the broader libs (search for it, find it, edit it, save it), but that doesn't seem to work with the easyEda symbols. The most intuitive approach would be for the editor for the Schematic Library to allow pasting a symbol the same way that the regular Schematic editor does. #Schematic#
mesopcb 2015-08-11 02:14:42 comment 4 0 Circuit Design
Slight improvement for file close dialog
Feature Request Brief title for your desired feature: Slight improvement for file close dialog How would you like the feature to work? Now, when one closes an edited file, a dialog pops up with the choice to "ok" or "cancel." I would prefer choices: "save", "abandon" or "cancel". In the current form, "cancel" is a bit confusing - is it canceling the work that was done, or canceling the request to close the file? Why is this feature important to you? It would be a bit less confusing, and a bit more consistent with other UI's that I have seen. This is very minor. I am a new user and am very, very please with the product! I just offer this as a minor improvement. #FeatureRequests#
mesopcb 2015-08-10 18:02:28 comment 5 0 Feature Requests
Metric grid and snap are not centered at zero
BUG Concise problem statement: On PCB, when using mm measurements, the grid and snap are not aligned to 0,0 Steps to reproduce bug: Open a new PCB editor. It will come up in English units (in or mils) Switch units to mm Grid does not align with 0.0,0.0 Results: Expected results: Browser: #BugReports#
mesopcb 2015-08-10 17:50:14 comment 7 0 Bug Reports
New PCBLib Part not available in Package Search
BUG Concise problem statement: After creating a new footprint as a PCB Lib, it does not appear in the package list when modifying schematic library symbol Steps to reproduce bug: Create a schematic library symbol and add a package name. Save it. Create a footprint/package using PCB Library. Save it. Edit schematic library symbol. Modify package name to bring up list of packages with search dialog The new footprint/package is not shown in the list. Results: Expected results: Browser: #BugReports#
mesopcb 2015-08-10 17:48:30 comment 2 0 Bug Reports