asdasdasd
Design Rule config file
Hi, I am just starting to try the recent EasyEDA Pro. Is there any publicly available Design Rule config file that matches JLCPCB maximum capabilities, like minimum via size, etc.? Thanks #PCB#
mwon 2022-05-22 19:59:35 comment 1 0 Circuit Design
Prodution delay
Are you experiencing a production delay? My last orders have taken a longer time than expected. I currently have an order yet to be finished, when it was supposed to be finished the last 4th of March. It is a 4 layer PCB board that was supposed to have a build time of 4 days. #PCB#
mwon 2022-03-08 12:13:45 comment 2 0 PCB
Feature request: add solder paste to the pads of non soldered componentes
This is a feature request I think it would be very helpful and that I think is currently not supported by SMT Assembly. When we order a PCB with SMT Assembly it happens many times we don't request the service to solder all components. The non-soldered components are later soldered manually by us (without the use a of stencil). Such a situation is fine if these components are big enough to be soldered manually. However, several times they are not. Sometimes for example I want a particular MCU that comes in a UFQFPN-48 that is quite hard to solder. One technique to solder these types of components is to add solder paste to the pads, melt it, and then place the component and apply again hot air. An example can be seen here. Although it seems easy, it is difficult to add the correct amount of solder paste. If too much paste is added, it results in pin bridges. The feature request is very simple: For those components that we do not want SMT Assembly, we could have the option to add solder paste. This would result that the pads of these components will be added to the stencil and filled with a good quantity of solder paste. Then, when in the oven, the solder paste will be melted and the PCB board shipped with it. When we receive the board we just need to place the component in the correct position and apply hot air. #FeatureRequests#
mwon 2021-11-30 12:36:09 comment 0 0 Feature Requests
Looking for a particular component
Hi, Not sure it's fine to ask about components. I'm looking for the component I'm showing in the photo I show below. It's a kind of support where the card will be fixed. I have no idea how this type of support is called. Any idea if the JLCPCB library contains this type of supporter? #PCB#
mwon 2021-10-05 11:27:00 comment 2 0 PCB
Board Thickness
How to change the default board thickness (set to 1.6mm)? #GeneralDiscuss#
mwon 2021-10-05 08:24:31 comment 11 0 Others
Define Differential Pair parameters
How can I define differential pair routing parameters such as trace width and trace space? #PCB#
mwon 2021-09-21 10:25:42 comment 1 0 Circuit Design
Minimum quantity order in the recent "Add to My Part Lib" feature
The recent feature "Parts Manager" feature is promising, particular for the many cases where we want to use a particular component that is out of stock at JLCPB. However, I noticed that the minimum quantities required of many components are of the order to thousands. For example, I'm working on a board that uses the MPU-6050 sensor that is currently out of stock for SMT Assembly. The minimum quantity to add it to My Part Lib is 5000 units! A full reel. Just like many of us here I'm a hobbyist. Why would I need 5000 units? Even for pros, JLPCB is used by many for prototyping only. I don't think they would order 5000 units. This type of requirement kills the feature and it would be nice if JLCPCB updated these minimum quantities to reasonable numbers. #PCB#
mwon 2021-08-25 08:09:55 comment 1 0 PCB
Change a through-hole component to the bottom layer but keep pin orientation.
Hi, I'm working with a 2x20 through-hole component available at JLCPCB (C35165) but I'm having problems with the pin orientation. My problem arrives when I put the C35165 to the bottom layer. This is the component's schematics: This is the PCB when the component is in the (default) top layer: And the respective 3D view: Now, I want to put it in the bottom layer but I can't find a way to flip and keep the same pin position. This is the PCB when I put it to the bottom layer and flip it 180º: And the corresponding 3D view: As you can see, the pin 1 position is not correct. So, how can I keep the pin 1 in the correct position and configure the component to be soldered in the bottom layer? I know that one solution would be to generate a custom symbol but I'm wondering if there is in EasyEDA any feature that would allow me to flip the component and keep the pin orientation. #PCB#
mwon 2021-08-02 10:43:33 comment 12 0 Circuit Design
How to draw a multi-layer pad with top pask mask
I have a PCB but the stencil that is drawn from it has some missing pads. The pads that are missing are the ones that I have defined as multi-layer pads. If I change these pads to the top layer, they show up in the top past mask layer but if I change again to multi-layer, it removes the pad from the top past mask layer, and consequently, the pad is not drawn in the stencil. How can I configure a multi-layer pad to be present at the top paste mask layer? #GeneralDiscuss#
mwon 2021-01-14 23:54:38 comment 2 0 Others
Assign via to net where the mouse is located when create a new via
For several cases, we have to add many vias before routing. It would be a good feature to assign automatically the via to a net at the moment we create the new via (V key) (like in kicad). If the mouse position is above some particular pad, then the via would assign to that net. Currently, this is done only if we click on the pad but that means that the via is placed and then we have an additional action to select it again and move. #FeatureRequests#
mwon 2020-12-17 11:18:52 comment 1 0 Feature Requests
How to pre-defined tracks widths
In kicad we can pre-define the track width and then select which one we are using while routing. Is it possible to do the same with EasyEDA? I don't want to define a fixed width for some particular net, because sometimes the same net can have different withs. I want to quickly choose the width as I'm routing. #GeneralDiscuss#
mwon 2020-12-17 02:10:18 comment 6 0 Others
Cancel SMT Assembly
I have an ongoing order of PCB production followed by SMT Assembly. I found an error in my design and therefore wanted to cancel the order and have a refund of the SMT Assembly part that does not event stated. I have contacted the customer services and they told me that I can't have a partial refund nor cancel because it's a single order. Why is that when it's two different processes? A big cost of the SMT Assembly will be components that will not be used. #PCB#
mwon 2020-12-14 10:43:02 comment 1 0 PCB
Route width design rule not being respected
I have set a single rule in the route design rule to make tracks of 0.40mm width. However, for some reason, when I draw a simple route, it is making routes with a width of 0.60mm. It might be related to the fact I had previously defined a design rule of 0.60mm. Although I have redefined to 0.40, it seems it's using the previous rule. The project is public and you can check it here: https://easyeda.com/miguelwon/battery-management #BugReports#
mwon 2020-09-08 09:21:08 comment 0 0 Bug Reports
Incomplete connections (GND and 5V)
I have designed the following PCB, added copper but it still complains about incomplete connections in GND and 5V. How do I get rid of these errors? The project: https://easyeda.com/miguelwon/atmega4809 #GeneralDiscuss#
mwon 2020-06-30 14:34:33 comment 2 0 Others
Unable to correctly simulate MOSFET
So, I'm trying to simulate a simple MOSFET behavior as a switch but I'm haveing odd values. I show below an image with an example. The Vgs for this MOSFET is 20V and so the current should be zero and the voltage 10V when the source is at 10V. #Simulation#
mwon 2020-04-14 21:58:13 comment 1 0 Circuit Design