asdasdasd
Add spinner to long operations
Feature Request Brief title for your desired feature: Add spinner when rebuilding nets, drc errors How would you like the feature to work? When refreshing the netlist (in PCB) or the DRC error list, it can take some time. Some kind of indicator such as a busy cursor or a changing the refresh icon to a spinner would be useful. Why is this feature important to you? It would be nice no know when a refresh operation is completed. Currently, I have to park the cursor over a dropdown menu so that I can know when the program is ready again. #FeatureRequests#
provideyourown 2017-08-31 14:25:11 comment 0 0 Feature Requests
Allow circles to be on other layers
Feature Request Brief title for your desired feature: Allow circle layers to be something other than signal or silkscreen How would you like the feature to work? In choosing the layer for a circle, allow any available layer to be chosen. This is the way rectangles work. Why is this feature important to you? I tried creating a fiducial with the solder mask pulled away as recommended by some, but placing a circle on the solder mask layer was not available. I even tried editing the layer via source file, but after closing and reopening the footprint, the circle gets deleted. #FeatureRequests#
provideyourown 2017-08-31 14:12:48 comment 2 0 Feature Requests
Flagging a component as favorite
Feature Request Brief title for your desired feature: Add footprint/package when marking component as a favorite. How would you like the feature to work? Currently, when flagging a component as a favorite, it only appears as a favorite schematic symbol. The footprint/package should also be made a favorite, or at least the option to do so should be available. Why is this feature important to you? It is very hard to figure out how to edit a PCB footprint/package. The reason is because when a component is marked a favorite, the accompanying footprint/package is not. When opening a favorite component, there is an editor for the schematic symbol, but not the footprint. This behavior is so confusing, that it makes it almost impossible to figure out how to edit a footprint. In fact, since component searching doesn't usually involve the footprint, it makes it even more difficult to figure out how to clone or mark a footprint/package as a favorite. If when making a component a favorite or cloning it, the option should be available to do the same with the footprint or otherwise a mechanism to do it with the footprint alone. Then, the footprint/package will show up in the component chooser under packages with the appropriate tag. Then it will be easy to create and modify one's own footprints. #FeatureRequests#
provideyourown 2017-08-31 06:42:19 comment 1 0 Feature Requests
Auto clean-up of traces
Feature Request Brief title for your desired feature: Auto clean-up of traces when editing How would you like the feature to work? Currently, traces are often created as multiple sections. When selecting a trace, only a given section is selected, even though the endpoints are the same. This behavior demonstrates that the traces while connected net-wise, are still separate entities. If they share the same end point, they should be merged when the edit results in such. Since the traces are not the same, when moving the connection point (or via where they connect) only moves the selected on or just the via if it is selected. What should happen is when connecting a new trace to an existing one is they become the same trace if the end points are the same. Likewise if a via is at the same point, the two traces should be separate, but moving either endpoint or the via should move them all at the same time. BTW, the same behavior applies to the schematic as well. Sometimes net connections to a pin become one, other times they are separate in that when moving one or the other, only one is moved. Why is this feature important to you? EasyEDA implements a novel way of handling connections in the schematic and PCB editor. Most programs maintain an internal entity that governs the behavior of subsequent edits. As a result, if they work it is great, if they have a bug, things get real messy. In contrast EasyEDA makes the internals match what the user does on the screen. I know I am not explaining it very well, but basically the EasyEDA way works better when it is buggy than do most programs. Unfortunately, it is still buggy. The nice thing is that it appears to still know what it is doing electrically anyway. Therefore, the only thing required is to change the graphical entities to match the already correct electrical entities. , #FeatureRequests#
provideyourown 2017-08-31 06:24:27 comment 0 0 Feature Requests
Ratlines appeared during editing that won't go away
BUG Concise problem statement: On a nearly completed PCB, the ratlines for an entire net (Vcc) appeared at some point. A careful inspection does not reveal any real connection problem. Steps to reproduce bug: Hard to reproduce. Make some edits to PCB, eventually they may cause nets to appear unrouted. Closing the PCB and re-opening solved the problem. Exporting as source and then creating a new file solved it as well. If desired, I can provide the source file, but it won't reproduce the problem. Results: Routed net shows as completed unrouted, not just a few connections. Expected results: Routed net connections should not show ratlines when still connected. A workaround was to close the file and reopen it. A refresh button would be useful in this case if the bug is too difficult to fix. Browser: Vivaldi #BugReports#
provideyourown 2017-08-31 06:10:40 comment 1 0 Bug Reports
Way to connect different nets in PCB without merging
Feature Request Brief title for your desired feature: Means to connect two different nets without merging them. How would you like the feature to work? A special schematic component which has two pins - one for each net. In the PCB the two nets would need to be connected to satisfy the netlist. Alternatively, allow the user to create a component with a footprint connecting the two nets with copper in the footprint. Currently, when attempting this latter method, the PCB editor flags this component and its connections with several DRC violations. Why is this feature important to you? When doing mixed analog/digital circuits, the analog portions often require isolation from the digital portions, but at some time their supply and ground connections must be joined. Requiring both to be the same net in the schematic causes confusion and makes proper PCB layout more difficult. A second use case is when connecting schematic pages or reusing a schematic module. The net names on one page or module may not match the ones on the other page. There can be a number of reasons to do so, most likely clarity. For example, connecting pins between two ICs - one IC may use one name and the other a different name. When connecting by name which one should be used? Often it would be best to name them differently and then connected them up. A zero ohm resistor is how many designers accomplish this task. However, that requires another component to be placed during assembly. It would be nice just to be able to do it in the program. If you look at the Eagle schematic and layout for the Arduino Leonardo, you will see they do this magically somehow. #FeatureRequests#
provideyourown 2017-08-31 05:48:19 comment 7 0 Feature Requests
Design Rules for Holes
What are the design rules for via hole sizes? The default seems to be 0.305mm, but the default vias being placed are 0.300mm. Which is the right value? If the via size is wrong, is there a way to change all of them at once? Also, are the default design rules the correct ones for PCB fabrication with EasyEda? #PCB#
provideyourown 2017-08-19 07:55:10 comment 1 0 Circuit Design
Changing layer settings unconfigures top & bottom layers
BUG Concise problem statement: Changing the layer settings results in the top & bottom layer becoming 'unconfigured', i.e. they are no longer visible in the layer toolbar. Steps to reproduce bug: Open the layer settings dialog. Make a change - color or marking a layer configured. Save settings. To fix: Open source file and change the 3rd flag in the top & bottom layers to true. Results: Top & bottom layer have disappeared from the layers toolbar. Expected results: Top & Bottom layers to not be changed. Browser: Vivaldi #BugReports#
provideyourown 2017-08-18 08:07:16 comment 5 0 Bug Reports
Join two copper pours on different nets
I am designing a circuit that has a sensitive analog portion, and therefore requires a separate ground from the digital portion. The two grounds need to be joined in the PCB at a single area under the chip. I do not want to merge the two nets, but want to connect them physically with a copper rectangle nevertheless. Is there a way to do this without merging the two nets? Thanks, Scott #PCB#
provideyourown 2017-08-18 07:22:54 comment 1 0 Circuit Design
ReAnnotation Moves Existing Components in PCB
BUG Concise problem statement:Updating PCB after re-annotating schematic moves the existing components. Steps to reproduce bug: Create schematic and generate PCB. Move components in PCB to desired locations. You may have to manually change some annotation in schematic so it changes on re-annotate. Save and update PCB. Check to see if components are in same location. If not, move them (this would be the same bug BTW). Re-annotate schematic and update PCB. Results: Components whose annotation changed have moved. Expected results: Components should not change position in PCB on update just because their annotation has changed. Browser: Vivaldi #BugReports#
provideyourown 2017-08-18 03:41:48 comment 3 0 Bug Reports
Better Operation Indication
Feature Request Brief title for your desired feature: Better Indication for Operations How would you like the feature to work? 1) The cross cursor feature is nice, but incomplete. It is not really a cross cursor as it extends completely across the page. Turning it off also turns off the indication aspect. The choice should be between a cursor that extends across the screen or a simple cross cursor. When no operation is pending, the cursor is an arrow. When an operation is in effect, the cursor becomes either a regular html crosshair cursor or the existing extended one, depending on the menu setting. In other words, when the cross cursor is turned off, the cursor still needs to change to an html crosshair during an operation. 2) When selection an operation in a tool palette such as wiring, that choice should be highlighted in the palette. That way a user always knows the operation in effect. Why is this feature important to you? I don't like the existing cross cursor indication, but with it turned off, I have no UI feedback as to what is going on. These simple fixes will rectify that problem. Number 1, should be trivial to implement. BTW, I have been using the program for a day now, and compared to all the others out there I really like it. Kudos for putting together a well designed package. There are still some rough edges, but I hope they can be smoothed out it time. Thanks, Scott #FeatureRequests#
provideyourown 2017-08-17 04:08:46 comment 1 0 Feature Requests
Backspace key is not captured
BUG Concise problem statement: Typing the Backspace key results in the browser going to the previous url. If there is any unsaved work, it is lost even if the browser fwd button is pressed to return to EasyCad. Steps to reproduce bug: 1.Open an easycad schematic and make some changes. Do not save. 2.Press Backspace key in a browser where this key causes the previous url to be opened. 3.Using the browser's fwd button, return to EasyCad. Select the schematic that was opened. Changes are lost. Results: The browser is operated by the backspace key, resulting in lost changes. Expected results: Backspace should be captured if not in an edit box. Alternatively, a javascript dialog should open confirming that changes will be lost with the option to cancel. This behavior is implemented in Wordpress for example when navigating away from a page with unsaved changes. When using one of the program dialogs where it appears that text can be deleted (but in fact cannot) with the backspace key, this bug can result in lost work. Browser:Vivaldi on Kubuntu 16.04 #BugReports#
provideyourown 2017-08-17 00:46:00 comment 2 0 Bug Reports
Moving component by keyboard breaks connections
BUG Concise problem statement: Steps to reproduce bug: 1.Place 2 components in schematic 2.Wire them together 3.Select one component and move via arrow key Results: Wiring to the component doesn't move and connection is broken Expected results: Wiring to move with component like it does when component is moved with mouse drag. Browser: Vivaldi on Kubuntu 16.04 #BugReports#
provideyourown 2017-08-17 00:34:22 comment 3 0 Bug Reports