asdasdasd
Forgot how to . . . .
Dillon/Andy I have forgotten how to match a schematic symbol with the PCB symbol. I imported them from the EDA library (both by same contributor). Getting an error in schematic when I try to convert to PCB. Thanks in advance, Ken #PCB#
reefhermit 2016-09-22 08:47:58 comment 5 0 Circuit Design
Recovering a Deleted Project
Is it Possible?? Thanks, Ken #GeneralDiscuss#
reefhermit 2016-09-22 07:47:51 comment 2 0 Others
keep Out
Is there a way to specify an area on the PCB to prevent traces from laying down AND the ground layer? I suppose this would be an all inclusive "keep out". Thanks, Ken #PCB#
reefhermit 2016-07-21 15:06:42 comment 10 0 Circuit Design
Forking a Project
Andy or Dillon, How (can) I change the Project name after forking? Thanks, Ken #GeneralDiscuss#
reefhermit 2016-07-17 16:16:40 comment 4 0 Others
Selecting a header from the library
I cannot put a "through hole" header on the schematic from the library. I only have the choice of a PCB header. I built my schematic from this library before?? I tried other parts also with the same result? #PCB#
reefhermit 2016-07-04 21:58:55 comment 10 0 Circuit Design
PART OUTLINES
When using "rectangle" in PCB Tools it only draws a solid rectangle. I need to draw a part outline. Thanks, Ken #PCB#
reefhermit 2016-06-09 20:03:47 comment 3 0 Circuit Design
Connecting to net
Several net connections are not being made on the PCB . . . . any suggestions? Thanks, Ken #PCB#
reefhermit 2016-05-29 21:11:37 comment 8 0 Circuit Design
Holes in copper area
Can you explain why there are holes in the copper area? Is it important? I have not seen this on the previous PCB I had you make. Thanks, Ken #PCB#
reefhermit 2016-04-27 04:34:15 comment 1 0 Circuit Design
NETS NOT CARRYING OVER
Any solution or advice for nets that do not carry over to PCB other than manually entering each time I route? Thanks, Ken #PCB#
reefhermit 2016-04-06 18:50:50 comment 3 0 Circuit Design
Looking for ABS enclosure prototyping
Dillon Can you recommend a vendor I can work with to prototype my ABS enclosure? I have CAD files. Thanks, Ken #GeneralDiscuss#
reefhermit 2016-03-29 18:43:09 comment 1 0 Others
Copy/transfer a CAD PCB to easyeda?
I have a CAD file for the PCB that fits into an enclosure. What is the best way to copy/transfer a CAD PCB to the easyeda system or what would you suggest to layout components with good accuracy? Thanks, Ken #PCB#
reefhermit 2016-03-21 22:20:52 comment 3 0 Circuit Design
Deleting imported Text on Schematic
There is a piece of text labled test point on an Eagle schematic I imported. It creates a package error when converting to a PCB. I cannot delete it? Any ideas? Thanks, Ken #Schematic#
reefhermit 2016-02-14 22:46:10 comment 3 0 Circuit Design
Extra Ratline
I have a ratline running between 2 pins that were successfully auto-routed? #PCB#
reefhermit 2016-02-09 03:05:54 comment 2 0 Circuit Design
Inner Board Outlines Cutout Error
How do I make a cutout on the PCB for guide posts? Thanks, Ken #PCB#
reefhermit 2016-02-06 18:28:03 comment 14 0 Circuit Design
Auto Router time Out
The auto router runs to 34% and times out . . . . no tracks appear. Ken #PCB#
reefhermit 2015-12-09 22:10:04 comment 6 0 Circuit Design
BOARD SIZE DESIGN
How do I dimension an accurate (1 mm resolution)irregular board size? What I need is a tapered board from 40mm to 30mm. Thanks, Ken #PCB#
reefhermit 2015-12-06 17:00:07 comment 5 0 Circuit Design
Adding SMD to Library
I am adding a 12 pad SMD to my library but only have 3 choices in adding new "schematic library" when using the Symbol Wizard. My "pkg" is simply 12 SMT pads. After adding this pkg to my schematic I get an error asking to define the pkg when creating the PCB. Thanks, Ken #PCB#
reefhermit 2015-12-06 01:34:56 comment 1 0 Circuit Design
Question about PCB fab
In addition to PCB fab do you provide assembly services? If yes, other than the obvious design, what am I required to provide in the way of component part numbers. All components of my design have been chosen from your libraries some (or most) without part numbers and/or manufacturer info. Should I research these to completion or better to develop my own component list? Thanks, Ken #GeneralDiscuss#
reefhermit 2015-12-02 02:20:49 comment 25 0 Others
Copper Pour . . . . Not!
After selecting the area for copper pour and then Shift B . . . . no response, no error! Any suggestions why this is not working. Also, I do not get the parameter window for copper pour. Thanks, Ken #PCB#
reefhermit 2015-11-30 22:14:42 comment 3 0 Circuit Design
BOM Printing
Trying to print a BOM but "export" will not come back with anything when selected . . just keeps running. Also, cannot select the text in the BOM to copy over to word pad??? Thanks, Ken #PCB#
reefhermit 2015-11-30 02:06:13 comment 1 0 Circuit Design
Pins Do Not Match error
Can you see these 2 images? Ken #Schematic#
reefhermit 2015-11-28 05:11:33 comment 4 0 Circuit Design
Error when converting to PCB
Cannot get rid of error . . . The correct Board pkg is selected for Schematic USB-MINIB! Can you help? Thanks, Ken #PCB#
reefhermit 2015-11-28 04:08:54 comment 2 0 Circuit Design
Modifing a standard component
Can I modify, for example, a TO-39 pkg by adding a 4th pin? Thanks, Ken #PCB#
reefhermit 2015-11-27 20:32:30 comment 9 0 Circuit Design
Question
What is the difference between a net port and a net label . . is the port on the buss? A label is simply a label? Thanks, Ken #Schematic#
reefhermit 2015-11-25 01:54:16 comment 4 0 Circuit Design