layer tool window
Hello, I have a problem with the "layer tool" window, while I am editing my PCB: When the mouse is not on it, there are 4 layers. When I move the mouse on it, the window is bigger and 8 layers are visible. But when I want to clic on "view" or "edit" of the 2 first (copper layer and component layer), the layer window reduced and my clic is not validated. So, I am not able to edit my board :( edit : the problem disapeared after some refresh of the page. #FeatureRequests#
net properties
Hello, I am looking for a net configuration function, I use on others electronic design softwares: It is the "net properties", where we can add easyly some properties to a signal ("VCC" for example) like the size, of the minimum insulation distance with others signals. Do this function exists in EasyEDA ? NB : I put this question in PCB Layout topic, but it should be in schematic, because generally this choice is done in the schematic. Or, maybe in Feature request... #PCB#
BSS138 N-MOS simulation
Hello, I nee d a N-MOS with a low Gate Threshold Voltage, but I did not found it in the library. So,I wanted to create mine, based on the BSS138, and I found a Pspice model (below) The problem is the simulation terminates with a timeout with this component (notwith another N-MOS). So,I would like to know if my problem comes from my model. Is there any warning or error message if there is a problem in the model ? Thank you. This is the model I found. .SUBCKT bss138lt1 1 2 3 ************************************** * Model Generated by MODPEX * *Copyright(c) Symmetry Design Systems* * All Rights Reserved * * UNPUBLISHED LICENSED SOFTWARE * * Contains Proprietary Information * * Which is The Property of * * SYMMETRY OR ITS LICENSORS * *Commercial Use or Resale Restricted * * by Symmetry License Agreement * ************************************** * Model generated on May 2, 03 * MODEL FORMAT: PSpice * Symmetry POWER MOS Model (Version 1.0) * External Node Designations * Node 1 -> Drain * Node 2 -> Gate * Node 3 -> Source M1 9 7 8 8 MM L=100u W=100u * Default values used in MM: * The voltage-dependent capacitances are * not included. Other default values are: * RS=0 RD=0 LD=0 CBD=0 CBS=0 CGBO=0 .MODEL MM NMOS LEVEL=1 IS=1e-32 +VTO=1.05059 LAMBDA=0.00404031 KP=0.269311 +CGSO=3.66018e-07 CGDO=7.50731e-09 RS 8 3 1e-15 D1 3 1 MD .MODEL MD D IS=9.63839e-09 RS=0.186581 N=1.76759 BV=50 +IBV=0.00025 EG=1.11237 XTI=1e-12 TT=7e-08 +CJO=2.07759e-11 VJ=2.77485 M=0.3 FC=0.5 RDS 3 1 2.5e+09 RD 9 1 1.83726 RG 2 7 6 D2 4 5 MD1 * Default values used in MD1: * RS=0 EG=1.11 XTI=3.0 TT=0 * BV=infinite IBV=1mA .MODEL MD1 D IS=1e-32 N=50 +CJO=7.71436e-11 VJ=0.523477 M=0.9 FC=1e-08 D3 0 5 MD2 * Default values used in MD2: * EG=1.11 XTI=3.0 TT=0 CJO=0 * BV=infinite IBV=1mA .MODEL MD2 D IS=1e-10 N=0.4 RS=3.00002e-06 RL 5 10 1 FI2 7 9 VFI2 -1 VFI2 4 0 0 EV16 10 0 9 7 1 CAP 11 10 2.46901e-10 FI1 7 9 VFI1 -1 VFI1 11 6 0 RCAP 6 10 1 D4 0 6 MD3 * Default values used in MD3: * EG=1.11 XTI=3.0 TT=0 CJO=0 * RS=0 BV=infinite IBV=1mA .MODEL MD3 D IS=1e-10 N=0.4 .ENDS bss138lt1 #Simulation#
PWL file
Hello, I want to use a PWL generator, with a lot of datas. So,I am looking for using a PWL file (A PWL file I use in Pspice). But I can not find it. Is it possible ? And how ? Thank you. #Simulation#
N-MOS simulation problem
Hello, I have a problem with a simple simulation: I try to load a capacitor and activate a N-MOS when the necessary voltage is reached. But when I simulate this, the high value of the voltage on C is around 1V instead of 5V. Maybe it is like a NPN transistor. But I put a MOS, not a bipolar transistor. do you know what is the problem ? Notice : If I remove the MOS, the capacitor is charged up to 5V. #Simulation#