schematic resize solution

There is much that I like after using EASYEDA for only a short time, but one of the disappointments was the lack of ability to resize the circuit elements to better fit within the page.  I also found tht the default "drawing page" wastes much space with large margins.

The solution to these "problems" for me and it is only a solution for printing/ease of viewing.  You need the free tool, "Cropper" which you can find at  https://cropper.en.softonic.com/ .  I have used it for years with Ancestry and found it to be completely safe and spyware/virus free.  You judge for yourself.

With this tool, I was able to place the cropper window over the area I was interested in or the entire drawing as I chose.  I could then double-click to copy that area to the clipboard.  The clipboard can then be pasted into Vizio or Word and probably many other programs.  Now this is just a bmp image, but once placed into Vizio or Word, it can be resized to better fit the printable space.

Again, I offer this to help another noobe frustrated by the lack of ability to resize what is seen on the screen. It does not solve the fundamental problem of being able to resize elements of the drawing, but it is useful for printing.  I have not tried this for the pcb design view, but I see no reason why it would not work.  vern

#General Discuss#
Others
Pease scope probe simulation is failing

I opened "Bob Pease's High Impedance Active Scope Probe simulations" from https://easyeda.com/andyfierman/projects, saved it to my workspace, switched to Sim mode and tried to run it...

To start with, it has a problem with the trimpot:

image.png

If I replace the trimpot with a library potentiometer, I get:

image.png

Orin.

#Simulation#
Circuit Design
Offset and amplitude in Sim mode Signal Generator is implemented incorrectly.

This Bug Report relates to:

https://easyeda.com/forum/topic/Signal-Generator-4d7e7398caba40f1a262469332a38dd9

Offset in the Rectangular and Triangle Wave outputs is not implemented correctly.

Both outputs of both waveforms are implemented using PULSE() sources.
The low and high level output voltage of a PULSE() Source is defined by the INITIAL and ON parameters respectively.
For an output with a peak to peak Amplitude, A, that swings equally A/2 above and A/2 below the Offset value, O, the expressions used to add an offset to the Pulse and Triangle Wave outputs should be:

INITIAL=O-A/2
ON=O+A/2

Offset in the Sine Wave output is implemented in an unexpected way.

For a function generator with two outputs in anitphase and a single offset control it would normally be expected that the same offset would be applied to both outputs and not - as is implemented at present - that one output would have a positive offset and the other a negative offset.
The Sine Wave outputs are implemented using the SINE() Source.
The offset of a SINE() output voltage is defined by the DCOFFSET parameter:
The expression to control the offset for both SINE() outputs should be:

DCOFFSET = O

The Amplitude of the Sine Wave output is double that of the Rectangular and Triangle Wave outputs.

The AMPLITUDE parameter of the SINE() Source represents the Peak value and not the Peak-to-Peak value.
Therefore for the Sine Wave output to give the same Peak-to-Peak swing as the outputs defined by PULSE() Sources, the expression for the SINE() Source Amplitude should be:

AMPLITUDE=A/2

For detailed information on SINE() and PULSE() signal sources in LTspice, please study:
https://easyeda.com/editor#mode=sim,id=5e3d25de3492487b88275e38c4620239
and:
https://easyeda.com/editor#mode=sim,id=d49a7278feef4be2b72d851765f3acbb
and for more information about sources:
https://docs.google.com/document/u/1/d/1OWZVVFRAe_2NW3WratpkA_SGuHa5AcRow5ZRfvcoVTU/pub#h.bq0i7caw31bh
 Reply

#Bug Reports#
Bug Reports