-
count of documents next to the project name? and move files from one project to another project https://easyeda.com/bbs_view_437.htm
-
Simply call it “Snap” (Yes / No), “Snap” is “No” the arrow keys must follow this minimum. Use the arrow keys - connection will break. Why? PINDO 在0,0 好像能被发现 . prefix 与 value 的位置需要调整 https://easyeda.com/bbs_view_438.htm
**BUG**
Concise problem statement:
Schematic seems to have invisible content in lower right hand area of canvas. It does not show up using any form of selection but when doing "Fit in Window", the schematic content of the canvas is pushed up towards the top left of the window.
Note also that it has been found to be possible to move objects off the edge of the canvas where they cannot be zoomed or panned to. They can then only be reached by doing Ctrl+A and moving everything across the canvas untill the off-sheet content is visible again.
It is therefore possible that the boundaries of the canvas have become corrupted in this process and that this may cause a similar effect to having invisible content.
Steps to reproduce bug:
- Open the attached schematic.
- Click "Fit to Window" to see effect.
- Not tat the effect is visible at any zoom setting.
It is not possible to state exactly what the steps were that led to this effect appearing as the schematic had been under continuous editing for some time before the effect was noticed.
Results: Schematic does not centre in the window at any zoom setting.
Expected results: Schematic should centre in window at largest zoom setting that allows the whole schematic to fit inside the window.
Url: https://easyeda.com/file_view_Astable-multivibrator-01_z93lCwO6o.htm
Browser:Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/29.0.1547.76 Safari/537.36
#Bug Reports#It can be difficult to put the mouse over the right place to highlight and select a component.
It seems that objects can only be selected by clicking exactly on the lines that make up their symbols and not on any spaces in or very close to them.
For example even at 150% zoom, it can be quite hard to find the exact spot to highlight the dashed line around PSU in:
https://easyeda.com/fileviewSingle-stage-NJfet-amplifier_w5ZhbtL3X.htm
The dashed line can only be selected by clicking on the dashes themselves, not on the spaces between them.
Extending the selection area around an object by some number of pixels around the object would help.
#Bug Reports#BUG
Concise problem statement:
The Preview of the PCB seems to show an earlier version OR does not draw floods even after reloading.
Steps to reproduce bug:
-
Open PCB file.
-
Note that PCB in main window has filled floods.
-
Note that Preview does not show floods.
-
Click Reload preview button.
-
Still no floods shown.
Results:
Main window shows floods. Preview does not.
Expected results:
Preview should look same as main window, just smaller.
Url:
https://easyeda.com/file_view_Astable-Multivibrator_9lfxP7pHB.htm
Browser:Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/30.0.1599.101 Safari/537.36
#Bug Reports#BUG
Concise problem statement:
Outline of bottom layer flood remains visible, drawn and selectable above top layer, even when TopLayer is selected in Layers toolbar.
Steps to reproduce bug:
1) Draw an outline for a top layer flood.
2) Copy outline.
3) Paste outline onto top layer.
4) Change outline to bottom layer:
5) Properties > CopperArea Properties > Layer.
6) Solid Fill bottom layer flood.
7) Switch to TopLayer in Layers toolbar.
8) Solid Fill top layer flood.
Results:
i) Outline of top layer flood remains visible as dashed line.
ii) Outline of bottom layer flood remains visible as dashed line.
iii) Outline of bottom layer flood remains visible, drawn and selectable above top layer.
Expected results:
i) After filling, outlines of floods should be drawn as sharp edges (through the centre of the dashes of original dashed lines?)
ii) Floods and/or flood outlines should move up and down consistent with Layers selection.
A lower layer should not be drawn above a higher layer if the higher layer has been selected in the Layers toolbar.
Url:
http://i.imgur.com/Hgtn5Be.png
https://easyeda.com/file_view_Astable-Multivibrator_9lfxP7pHB.htm
Browser:Mozilla/5.0 (Windows NT 5.1; rv:24.0) Gecko/20100101 Firefox/24.0
#Bug Reports#**BUG**
Concise problem statement:
Can't find a way to do a swept value of R1.
Trying to implement section 16.13.4.2 .step of ngspice manual:
http://www.ngspice.com/downloads/ngspice-manual.pdf
Note that spice netlist has lost indents for content of
.control .... .end
section. Don't know if that has any effect.
Note also that simulation runs OK as a simple non-swept sim and does not report errors.
.STEP R1 1k 2k 1k statement is commented out but has no effect if set to spice directive.
Steps to reproduce bug:
- Run transient simulation
Results: V(boo) only shown at 2.5V.
Expected results: V(boo) should be shown as 2.5V and 1.67V.
Url: https://easyeda.com/file_view_step-test-01_AysKEWevN.htm
Browser:Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/30.0.1599.66 Safari/537.36
#Bug Reports#