EasyEDA Does Not Display Extended Part Fee Status

The $3 Extended Part Fees can add up to a lot. I want to see the $3 status of every part I use. EasyEDA V2.2.45.4 client provides absolutely no way to see that. Every part in the schematics should have at least a read-only checkbox property for $3 fee status. The BOM Device Standardization and exports should include it. The library search window should have it. And the web BOM Tool should have it. None of them have it. They all should.

The only way to see $3 status is in parts search web page: a Basic type or blue thumbs-up in row indicates no $3.

I'm not arguing against a $3 fee. I think it makes business sense to incentivize users to consolidate on basic/promo parts. But JLC is remiss in making that determination unreasonably difficult. This problem has been extant for years.

#Others#
Others
MOTOR DRIVER BTN9990LV 75 AMPERE MAX, THE GREATEST MOTOR DRIVER EVERRR!!!!

Dual DC Motor Driver Using BTN9990LV

Full-Bridge Bidirectional Control and Performance Optimization


1. Overview of BTN9990LV

The BTN9990LV is a high-current half-bridge motor driver IC from Infineon based on Smart Power Technology. It is designed for reliable DC motor control in automotive and industrial applications.

Key Features:

  • Type: Half-Bridge Motor Driver

  • Operating voltage: 5.5 V – 40 V

  • High output current capability (up to ±75 A peak)

  • Integrated protections:

    • Overcurrent protection

    • Overtemperature protection

    • Undervoltage lockout

    • Short-circuit protection

  • Supports high-frequency PWM

  • Logic-level compatible (3.3 V and 5 V microcontrollers)


2. Full-Bridge Configuration Using BTN9990LV

Since BTN9990LV is a half-bridge device, a full-bridge (H-bridge) requires two BTN9990LV ICs per motor.

IC Requirement:

  • 1 bidirectional DC motor → 2 × BTN9990LV

  • 2 bidirectional DC motors → 4 × BTN9990LV

This configuration allows complete control of motor direction, speed, and braking.


3. Operating Principle of Bidirectional Full-Bridge

A full-bridge enables:

  • Forward rotation

  • Reverse rotation

  • Dynamic braking

  • Free-running (coast)

Control Logic Example:

IN_A IN_B Motor State
PWM LOW Forward
LOW PWM Reverse
HIGH HIGH Brake
LOW LOW Free running

PWM signals are used for speed control, while logic levels define rotation direction.


4. Basic BTN9990LV Circuit Description

Important Pins:

  • IN – Logic/PWM input

  • EN – Enable pin

  • OUT – Motor output

  • VS – Motor supply voltage

  • GND – Ground

  • IS – Current sense output

  • SR – Slew rate control

Typical Connections:

  • VS → Motor power supply (e.g., 12 V or 24 V)

  • GND → System ground

  • IN → Microcontroller GPIO/PWM

  • EN → Logic HIGH to enable

  • OUT → Motor terminal


5. Dual Motor Control Architecture

For two motors:

  • Motor 1 → BTN9990LV (A & B)

  • Motor 2 → BTN9990LV (C & D)

Each motor has independent PWM and direction control, enabling differential drive or independent speed regulation.


6. Performance Optimization Techniques

6.1 Power Supply Design

  • Place bulk capacitors (470 µF – 1000 µF) close to the VS pin

  • Add 100 nF ceramic decoupling capacitors

  • Use short, wide PCB traces for power paths

✔ Reduces voltage drop and electrical noise


6.2 PWM Configuration

  • Recommended PWM frequency: 15 – 25 kHz

    • Above audible range

    • Improved efficiency

  • Always use hardware PWM for stable control


6.3 Slew Rate Control (SR Pin)

  • Use an external resistor on the SR pin

  • Slower slew rate:

    • Lower EMI

    • Reduced thermal stress

  • Faster slew rate:

    • Faster motor response

✔ Select based on application requirements


6.4 Current Sensing (IS Pin)

  • Use the IS pin to:

    • Monitor motor current

    • Detect motor stall or overload

    • Implement software-based protection

  • Apply ADC filtering for stable measurements


6.5 Thermal Management

  • Use large copper areas on the PCB

  • Add thermal vias under the IC

  • Attach a heatsink for continuous high-current operation (>5 A)


6.6 Additional Protection

Although BTN9990LV has internal protection:

  • Add TVS diodes on the motor supply

  • Use fuses or polyfuses

  • Implement star-grounding topology


7. Advantages of BTN9990LV Compared to Conventional Drivers

Feature BTN9990LV L298
Efficiency High Low
Current capability High Low
Protection Comprehensive Minimal
Voltage drop Very low High
High-frequency PWM Yes No

8. Typical Applications

  • Differential drive robots

  • Automated Guided Vehicles (AGV)

  • Line follower robots

  • Industrial DC motor control

  • Smart actuators


9. Conclusion

A motor driver based on BTN9990LV is a robust and efficient solution for dual DC motor full-bridge bidirectional control. With proper power supply design, PWM configuration, and thermal management, the system achieves:

  • High efficiency

  • Stable operation

  • Reliable protection

  • Precise motor control

This makes BTN9990LV ideal for high-performance robotic and industrial motor applications.


Link:
https://drive.google.com/drive/folders/1PoshLd9N2BOwwoIAyyH2I7-uXxUVBLAV?usp=sharing

Writer:
Bintang Adhiyaksa Dani Saputro
+62822-2306-9220
bintangadhiyaksa@gmail.com

#PCB#
Circuit Design
(Feature Request) Multi-line PCB text justification in easyEDA Pro

Hello,

I'm having trouble with text justification in the PCB editor.
(Similar question to
https://oshwlab.com/forum/post/e1291aad5be745a888c97f8dbeb5901a, but in the pro version).
To be clear, I'm not trying to allign multiple pieces of text to eachother. I'm trying to allign multiline text to it's own bounding box, be it left or right and depending on the orientation up or down.
This is an example using a normal text editor:

Left justification Right justification
D1 D1

The applied example:

The text on the right side of the device is correct.
The text on the left side has left justification, causing it to leave a gap between the pins and the text.
Changing the origin (as done in the schematic editor) does not impact text justification (it does in the schematic editor).

I've used a workaround using a monospace font which I imported from the standard Windows fonts (cascadia mono) and added leading spaces to the text with the desired result:


Can PCB text justification be added?
It seems like a needed tool for a lot of users, and it is already included for remarks in the schematics editor.

Thanks in advance!

#PCB#
Circuit Design