Anyone recognise this component?

https://youtu.be/uSUwHh2TRRc



It's a 5050 case rgb led with an IC chip. Six pins. But it appears not to be addressable. It only performs the sweeping colour pattern seen in the video. I suspect it might be found in JLCPCB or LCSC component catalogs, but I can't figure out the search terms.
In the video I apply positive voltage to the right. You see the dent mark at the bottom right corner. In an ordinary 5050 rgb led array, the dent is at cathode side.
I'm most sure the very same led can be found in a garden light I have. A small lamp with a solar cell and some super capacitor. At daytime the solar cell charges the capacitor. At evening, when it becomes dark, the capacitor is discharged directly through this led.

#General Discuss#
Technical Discussion
Error in datasheet and in footprint

My bug report is about component C2843784, which shows the following info in the component catalog, under PCB Footprint or Symbol:
image.png

Here we can already see an error. To the left we see the symbol, telling us that pins 1, 2 and 3 are cathodes. To the right, pins 1, 2 and 3 have plus signs! When we open the datasheet, we get this image:
image.png
Here we see that pins 1, 2 and 3 are indeed cathodes. We also see that the MARK is at pin 1, the cathode side. In the footprint, the MARK is at pin 1, but it has a plus sign.
We can draw a conclusion that something is wrong here. We are always advised to follow the datasheet. And that would be the simplest thing to do. The simlest interpretation of this is that the plus and minus signs are wrong in the footprint.

But it gets worse, and this is either the same bug or a completely different bug, that's for JLCPCB, LCSC and maybe XINGLIGHT and EasyEDA to sort out. I ordered fifteen PCBs from JLCPCB, each one had three of these leds with component number C2843784. JLCPCB did the SMT assembly. When I got the boards, I noticed that the led was a completely different component. It was the type where you add voltage to any pair of anode/cathode pins and it starts to show a colour sweep pattern red-yellow-green-cyan-blue-magenta-red etc. With a help of an integrated chip inside the component.
I have tried to explain this error to the after-sales support, but they haven't so far done anything to actually track down where the error has happened. As I see it, we have a few options here.

  1. When JLCPCB made the SMT work on my board, they assembled the wrong reel of components. 
  2. JLCPCB used a reel with the correct product code, but the component provider (LCSC?) had made errors in labelling reels. I have tried to find the component in the catalogs, the component I actually got, with the IC chip and the sweeping colours, but haven't found it.
  3. Xinglight, which is the manufacturer, has mixed their products and product codes. Reading further in the datasheet, we can see that in the image from the datasheet above, we can see the chip (IC). We can further see that the component reel is described. Unfortunately I don't speak or read Chinese, but the components pictured in the reel in the datasheet are not 5050 components, but something smaller. That gives an impression that the datasheet is not very accurate. And that the component information from Xinglight has been wrong from the very beginning.

I only know that an error has been done somewhere. I leave it to JLCPCB to track down the error, because I have no way to actually track the error further.  I believe it's in everyone's interest to find the error.

#Bug Reports#
PCB
Pro Edition not working properly

Hi,

since a few days, the Pro edition has several issues, making it hard to use.
Here a project you can hopefully see the issues:
https://pro.easyeda.com/editor#id=28d9a2d7d1f44224ad6b57ee5fe313b2\,tab=edb1c7933884477193e3294bd8d7743d|*f96af4480eee4527888581f84cc276bf
or the invite
https://u.easyeda.com/join?type=project&key=f80ddb1afffe46eba9593ddc4ca9bd9c&inviter=536625a8218b45279923a4deedb6ac09



Browser: Firefox 105.0a1 (2022-07-28) (64-Bit) Windows 10

Regards,
g3gg0



Issues:

1. Board outline in 3D does not generate properly anymore

I can really not make out what has changed since then. I even recreated the outline, but still it incorrectly generates the cut.
The last thing i did before realizing it doesn't generate anymore, was removing something on the documentation layer.
before:

now:
grafik.png

2. 3D Models do not load anymore

Working before, i get these placeholder models now after 5 mins of loading:
grafik.png

3. Exporting 3D OBJ does not work anymore

It just "works" a few minutes, scrolling the bottom bar and i get no file to download.

#Bug Reports#
Bug Reports