hi i want to use a connector like this through a pcb.
https://i.ebayimg.com/images/g/jYMAAOSwxoJcdlbT/s-l500.jpg
i could make a pad in the correct size however it has part of thread cut away to prevent twisting i would like to
create the correct profile but just cant seem to get to work.
would like to use the ground on the pcb through the connector.
any help would be very welcome the headache it is causing is hurting now
#PCB#I made a design, which included an SMD RGB LED. I happened to choose the item C2843784 found on LCSC catalogs. My intention was to order the PCB with all SMT part mounted and for some reason that was the only component I found that JLCPCB accepted. I was in hurry, so I didn't dig deeper after alternative parts. The problem was that the datasheet, the schematics and the footprint didn't match each other!
This is how the footprint looked like:

The red arrow and the ellipse are added later to point out the error when I chatted with the customer support at JLCPCB. As you can see, the left schematics show that pin 1, 2 and 3 are cathodes. The right footprint shows plus signs at pins 1, 2 and 3. But the footprint shows the dot and the triangle mark at pin 1. All SMD RGB LEDs I have worked with have the triangle mark at the cathode side. So it was only natural to assume the error was with the plus and minus signs in the right footprint. Because there was an error somewhere! Furthermore the datasheet of the item C2843784 shows that the triangle mark is at the cathode side!
My error was to rely on the customer support at JLCPCB. They said I should follow the datasheet, which showed this image:

So I went and ordered my PCBs, fifteen identical PCBs, each having three of these leds. And when I got them, they were wrong! The triangle really points out the anode, not the cathode!
It is my believe that the manufacturer has made an error placing the triangle mark at the anode side. The error is not that big, if all datasheets, schematics and footprint thoroughly followed that! But now the people, who made the datasheets didn't notice the unconventional (but probably not erraneous) marking and they messed up everything. And I have 15 useless PCBs.
After I pointed out the error to JLCPCB (which further reported it to LCSC), the footprint has been corrected, but the datasheet still is wrong (check it yourself), at least at the time of writing this. I even got a thank letter from LCSC for pointing out the erraneous schematics/footprint combo, but at that point I had already ordered my PCBs with wrongly placed leds. And to me, their correction still looked wrong because the plus signs were still at the triangle mark side (which turned out to be the right way!)
Lesson learned: Don't trust anything, as long as the datasheet, the schematics and the footprints and all pin numbering don't match each other in the component catalogs of LCSC or JLCPCB! Have them correct the info on all places before you rely your PCB design on the info. Don't trust advice from the customer chat.
They do a good job! The chat at JLCPCB responds quickly and they got LCSC to correct the footprint rather quickly. But in my case, due to production schedules, it wasn't quick enough.
#SMT#Hi,
When importing a design from a KiKad project, all of the components on the PCB are set with X Y Location = 0.
This means that when a component footprint is changed, for example when swapping an existing component to be a component from the LCSC library and selecting that footprint, and that update is subsequently applied to the PCB the 'Replace Component' operation places the replaced component at 0,0 on the PCB. So, if you replace multiple components, they all get moved to 0,0 on top of each other.
For example, I import this KiKad project: https://github.com/AnaviTechnology/anavi-light-controller, I then update some of the footprints/components to be LCSC compatible components, and I update the PCB. All the components get moved to 0.0 when 'Replaced'.


Selecting the connector on far right - location is 0,0. This is the same on ALL components on the board.

Project shared as: https://oshwlab.com/julian.n.robbins/ANAVI-Light-Controller
Thanks,
Julian
Hi,
I finally managed to import a project from Std to Pro version of EasyEDA ( https://oshwlab.com/mijnmodelbaan/mega_motor_n or https://pro.easyeda.com/editor#id=b14a59c4633d40fe93ae8cca917d5cfd ).
I checked the footprints, updated the PCB, corrected the errors and saved everything. Closed editor and went to bed.
Opened the project again this morning and checked the PCB for changes in the schematics (standard routine for me).
To my surprise there were errors! So somehow the changes weren't saved or I made a mistake myself.
So went to the schematic, clicked [Design] > [Update/Convert schematic to PCB] and found there were some 20 'Update Net' actions on the list, about half of the number from yesterdays list.
I did then have a better look at the list and found all the 'After import' fields are empty:

What am I doing wrong - what's (not) happening here - what did I forget ?
There are 2 boards in the project. Each board has 5 components which go onto the PCB. Both boards show the same behaviour during updating.
Thanks in advance,
BR//Willem.
[solution]
The new concept of 'devices' solved this. I was using the imported symbols and footprints and this caused the error. After replacing the L1 component with a newly created device all worked fine.







Hey, I made a schematic for some sort of console/devkit, I'm sorry if you're supposed to ask another way,
