From topics like those listed below, it is clear that a component is needed which can split a net into two separate nets in the same way as a 0 Ohm resistor or a series component as part of an impedance matching network but which is in fact just made of copper.
https://easyeda.com/forum/topic/How-to-design-a-PCB-Lib-for-a-PCB-Antenna-efa50ba1cdd9433c958ceedbad520398
https://easyeda.com/forum/topic/Inconsistent-connection-to-pad-on-single-numbered-multi-padded-footprint-40071cd5cf5a478cac7be7d4334a02a1
https://easyeda.com/forum/topic/How-to-avoid-DRC-errors-when-connecting-to-PCB-Footprints-a-k-a-PCB-Libs-90bf944fe3644b21a7d27a9e9d8df8d6
https://easyeda.com/forum/topic/Non-exposed-coper-vias-in-footprints-341192f38fb04a1b8addae2065ba400c
At the moment a 0 Ohms resistor or a series component as part of an impedance matching network works OK because it has two separately numbered pads that are not connected in the Footprint by copper.
However, any attempt to replace that with a copper element:
- results in warnings about more than one name on a net and;
- generates DRC errors.
What is required is a footprint which has two separately numbered pads that is joined by a copper element BUT for which:
- no warnings are given about multiple netnames and;
- DRC errors are not generated flagged
Apparently there is such a component in Kicad called a "net-tie".
A net-tie in EasyEDA would solve a lot of problems in things like connecting to PCB antennas and splitting ground areas.
Such an element would have to have a parameterised width to match trace widths into which it is inserted and a parameterised distance between the two pads.
The net-tie element would:
- be a single layer element only. There is no need for it to be a multilayer element;
- be possible to place onto any layer;
- have to have a parameterised width to match trace widths into which it is inserted and;
- have to have a parameterised distance between the two pads;
- work with traces, solid regions and copper Areas;
- if possible work inside a PCB Footprint (a.k.a. PCB Lib).
I am currently adding an NFC antenna to my board. However, I cannot connect one of the pads of my antenna to the corresponding component.
Indeed, when I want to connect the top pad of this antenna, a yellow cross appears, while it works for the bottom pad. However, I have associated the antenna schematic to the footprint. Can you help me ?
Click here to see my component:


Here is the DRC error I get:

Hi,
I've got an updated model to my 12V Automotive Timer Simulation here: https://easyeda.com/Dkraemer/timer-rev-b
I'm having a lot of trouble with the transient simulation settings. Whether or not the simulation runs seems to change day to day. I don't think I'm making any changes that would affect the circuit so much that I'd get a 'time step too small' or "circuit too complex" error.
Is there a more definitive guide to transient spice setups? I've not been able to find a pattern and the help file isn't useful or clear. It says: (Stop-Start)/time step<10,000, but I don't know how to use that, especially when ".tran 0 15000 10m" runs, but not ".tran 15000". If I enter the first parameters into the simulation setting box (start time is 0, stop time is 15000, max time step is 10m) I get the "time step too small" error.
I've been banging my head against my desk and have searched the forums, the help files and google for this but I can't figure it out.
#Simulation#I'm not sure where the bug is however from the appliction use Print -> PDF Preview and the schematics are either very up to date or incomplete.
The same images are being used on project home page - so the public homepage for my project looks like it's half complete. All of the schematics are wrong. Take a look at https://easyeda.com/peterw8102/8bit-video-card - scroll down to the images. Affects the PCB image as well.
Doesn't affect my other public project.
#Bug Reports#My project has a lot of SMT components on the bottom face.
I started a JLCPCB SMT assembly order using a pick-and-place file generated using the default options.
All components are in the right place (no need to mirror coordinates) but are rotated 180 degrees.
I do not know whether this is an EasyEDA or JLCPCB bug, but one could have an option to mirror the rotations angle for bottom components, checked by default.
The project is at https://easyeda.com/account/project/detail?project=d16853fa02744609adb2594b33fadbd2
Feel free to email me if you need the specific files.
Thanks.
#Bug Reports#







