Using Solid Region set to No Solid creates multiple DRC error when used in a PCB Footprint

I have two versions of a footprint, version 1 using two pairs of Top and Bottom layer pads via'd together and version 2 using Multilayer pads with a single Auto-placed via joining top and bottom layers. Both now have the central 13mm hole in place.
image.png

The footprint should have a central cutout as in the drawing below:

T10 footprint in color measurements.jpg

In both versions, the central cutout shape is created by placing a 13mm diameter Hole and also placing a Solid Region with radiused ends on the same 0, 0 centre. 

The JLCPCB Gerber viewer shows that in both of them, the central cutout shape is correctly formed: 

image.png
There's a Schematic Symbol with the version 2 footprint assigned to the Package attribute and a simple schematic and PCB that demonstrates it together with the same symbol but with the Package attribute edited to assign the version 1 footprint to it:
image.png
image.png
The schematic converts to PCB OK but there are lots of DRC errors in both footprints caused by the Solid Region set to No Solid. You can safely ignore them but I believe that using the Solid Region Tool in this way in a PCB Footprint should just not create these DRC errors.
image.png

I was going to try use the Arc Tools to create the required round ended slot directly in the Board Outline layer to replace the Solid Region to see if that avoided the DRC errors but after updating to V6.3.39, I can no longer easily create such a shape. 

In fact I originally used the Arc Tools to create the shape that is now created by the Solid Region but didn't check it to see if there were any DRC errors. Then I had the "better" idea of using the Solid Region tool but that was yesterday using V6.3.22. Now having auto-updated to V6.3.39, I no longer have the option of going back to trying the direct Board Outline approach.

I have raised a separate Bug Report about the loss of functionality of the Arc Tools.

#Bug Reports#
Bug Reports
Since V6.3.39, Arc tools are almost useless

In the What's New release notes for V6.3.39 it says:

  • Change the ARC interaction logic, keep the center of the circle unchanged when edit the start/end point; Adjust the properties panel properties options

In V6.3.22, I used the Arc tools to easily create accurate rounded ends to a rectangular cutout. I could do this because I could independently specify:

  • the start XY coordinates;
  • the end XY coordinates;
  • the centre point of the circle on which the arc lay;
  • the radius

I could also specify clockwise or anticlockwise direction that allowed inside or outside segments of the arc to be created
I could also specify the start and end angles of the arc with respect to the centre of the circle on which it lay.

With V6.2.39 I cannot independently specify the start XY coordinates and the end XY coordinates. Now there is only the option to specify the start and end angles of the arc with respect to the centre of the circle on which it lay which means that if I change the radius, the start XY coordinates and the end XY coordinates change.

Most people do not think in terms of Polar Coordinates and the Canvas does not support them anyway so unless I do some very complex trigonometry to work out where the start XY coordinates and the end XY coordinates are going to be given the centre, the radius and the start and end angles, it is no longer possible to accurately position an arc of a defined radius.

I can do the same job by editing the points and Arc segments in the Solid Region tool but I particularly wanted to use the Arc tools to create a shape directly in the Board Outline since in one particular application in a PCB Footprint, the Solid Region set to No Solid was giving multiple DRC errors and I suspected that creating the same shape using a Board Outline directly would not.

Please reinstate the Arc tools functionality of V6.3.22 or add a switch to allow different modes of use.

Thanks.

#Bug Reports#
Bug Reports
How to add a diode Zener?

Hi Everyone,

I am new to EasyEda and I started to do some simple circuits. I want to try a simple 12 V Diode Zener circuit with a Zener and two Resistors and 15 V DC source. Here the circuit:
https://easyeda.com/sasadangelo/simplezener

The problem is that I don't find it in EELib. I searched in SpiceLib but when I add to the schema and start the simulation it says that it is not in EELib. I noticed there are a lot of people use Zener in their schema, how I can do it? How I can use Diode Zener with common voltage 2.4, 4.7, and so on?
Another thing I want to do is check the output voltage when the output resistor value increase or decrease, to do that I want to use a vbProve but it's not clear to me where to find the voltage value.
Thank you in advance for your help.

#Simulation#
Circuit Design
【Update】EasyEDA editor v6.3.39 released

**What's new in v6.3.39**

2020.04.21

Important Notice

  • Before v6.3.39, update PCB is made through the component prefix, at now, it is made through the component unique ID now. After opening the old document for the first time, the editor reassign the component ID based on the component prefix
  • If the old schematic pages contain subparts(such as U1.1, U1.2 combine as a U1), the component need to be manually moved back to the original location after the first Update PCB
  • Before modify the old projects, suggest to create a new version for it, then edit the new version. Via: project list - project folder - right-click menu - version
  • Release new desktop client v4.1.8, supports to save project to local, change the client mode at Setting menu. Only Windows platform avaliable, Linux and Mac OS need sometime.

Improvement

  • Support to remove 3D model at component property panel
  • New Import Changes logic, fixed component location will offset issue after Import Changes(for the old documents, please open and save them; known issue, for the subpart, after Import Changes have to move the footprint back the location)
  • Fix after Import Changes the net of track doesn't update issue
  • Change the ARC interaction logic, keep the center of the circle unchanged when edit the start/end point; Adjust the properties panel properties options
  • Update Design Manager error and warning description
  • Change V-CUT clearance default value as 2mm
  • Support import 3D model in batch:WRL files need to be compressed to a zip fie, no more than 10 WRL files per zip file
  • Support set the unit for the 3D model when importing
  • 3D Model Manager support one-click to auto fit the location
  • SIM mode and STD mode support to switch directly, doesn't need to close documents first anymore
  • Remove Via entry at PCBlib
  • Fix rotate the whole PCB will offset some objects issue
  • Fix some Altium File will show some errors at Design Manager issue
  • Fix when place schematic module will appear incorrect Netport issue
  • Copper area and solid region drawing corner follow with the right-hand panel routing corner
  • Fix CTRL+F dialog will disappear issue after search
  • Fix fail to set canvas zoom effect as Quality Priority issue
  • Fix 3D Manager the model outline location doesn't match footprint issue
  • Fix when just export solder mask layer to PDF, the exported file no content issue
  • The BOM content is contained by double quotation marks
  • When the PCBlib has been updated, after Import Changes, will pop up a dialog waiting for update
  • New EElibs, all assigned the 3D models
  • Fix the problem that you can still click on a selected device after hiding the top or bottom layer
  • Fix the PCB size doesn't contains panelized boards size issue
  • Fix the problem of lost line wrap after modifying the properties panel after normal text line wrap
  • When Import Changes, instead of directly replacing the package with the update, a pop-up window is listed and waiting for the update
  • CSV file contents of exported BOMs are included in double quotation marks
  • Circle drawing supports to use - + to change track width
  • Fix PCB export as SVG will lost copper area issue
  • Fix some schematics export as PDF fail issue
  • Fix some fail to import Altium files issue
  • Fix other issues
#General Discuss#
Others