Okay, on a more complicated circuit I accidentally had a probe on a wire that was connected to ground, but kept getting the message"Probe can not connect with ground (GND)!". So I kept moving it closer to ground with fewer and fewer components. Finally realized its the error message that is misleading and incorrect.
After reading the Simulation eBook https://docs.google.com/document/u/1/d/1OWZVVFRAe_2NW3WratpkA_SGuHa5AcRow5ZRfvcoVTU/pub#h.1y810tw (following advice on the Posting a Question sticky on the forum) under Probing Voltages, it states:
>In spice simulations\, all voltages are referred to ground so not only is there no need
to attach a Voltage Probe to the ground net, in fact doing so will throw an error in the simulation.
..but is the same error being returned for "no connect to ground" as "connected to ground"?
Also, fyi, the first tutorial listed in the page below is returning a 404 error. @andyfierman
https://easyeda.com/example/Simulation_Quickstarter-iLN8usOaw
https://easyeda.com/example/Spice_tutorials-AysKEWevN
Hello, I've looked all around and searched google and the forums, but I cant seem to get to the custom attributes for a component using the online editor (is it not available online?). I must be missing something simple, because it there's no special mention of an extra setting in the tutorial: https://docs.easyeda.com/en/Schematic/Component-Attributes/index.html. Any help appreciated, thanks.
BTW, I'm just trying to build the most basic LC oscillator, so I know the simulator works as expected, using a V controlled switch. I have to change the parameters in the switch to turn off after the programmed pulse from the V1 goes from 1 to 0.
I'm following the instructions from below\, and its weird because I can view the Custom Attributes on the projects below. I've even tried copying and pasting from them into my project. And also importing the Voltage_Controlled_Switch form the library contributed from andyfierman\, with no luck.
https://easyeda.com/forum/topic/Switching_during_simulation-LHhCAyUge
https://easyeda.com/example/How_to_simulate_a_DPDT_switch-Wgs2CbLlH
https://easyeda.com/andyfierman/Setting_up_switches-oW8SPbxTf
OKAY!!!, nevermind.. I'm going to submit this for future others, but I was using the Simulation mode (because why have to toggle between the modes for iterations of changes). Ironically, though Ive been at this for a couple hours, the forum wouldnt let me post, Im assuming because Simulation mode doesnt count for the 30-60 min threshold of trying before asking for help. Anyway, upon switching back to test if that was the case, It dawned on me that maybe Custom Attributes are only available in the design mode. Although, still confusingly inconsistent to be able to access the other examples in Simulation mode(?). Anyway, it worked and I can move on..
https://easyeda.com/editor#id=c12f25b311704912bee3a904b35132d9
https://easyeda.com/editor#id=c12f25b311704912bee3a904b35132d9
Hello everybody.
This is a circuit where a clockwise rotating
field (LED 1 lights up) or the left rotating field (LED 2 lights up) of a
three-phase motor / connection can be displayed. I am new to electronics and I found that simple circuit that I do not
understand, so I would like to simulate this circuit to understand the function
of the capacitors and diodes.
I've already looked for tutorials on google and youtube, but I can't find an explicit solution to my problem. Then I started to read the The EasyEDA Simulation eBook article\, so I had my first positive experiences and results with the **waveform tab. **
My current problem is that I don´t know exactly how and where I correctly define the measuring probe and ground for showing me at wich time, how much Volt and Ampere is present at the LEDs.
Here you can find a link to the original circuit that I wanted to recreate: https://upload.wikimedia.org/wikipedia/commons/archive/5/57/20160922134435!Schaltung_Drehfeldmessgeraet.svg
Thanks for your help.









