One of the most frequently asked questions about EasyEDA is how to find a Schematic Symbol or a PCB footprint for a particular component.
This is always a difficult task in any EDA tool.
In EasyEDA, the Design Flow is based on finding the Schematic Symbols (Sch Libs) and PCB Footprints (PCB Libs) first, before starting on a Schematic.
If suitable Schematic Symbols and PCB Footprints are not available then the required PCB Footprints should be created first followed by the Schematic Symbols.
This is because when the Schematic is drawn each Schematic Symbol that is placed in it must have a Package (a.k.a. PCB Footprint) assigned to it. Then, when the Schematic is converted to a PCB, all the correct PCB Footprints are automatically pulled in based on the Package assigned to each Schematic Symbol’s Package attribute.
Therefore to create the Schematic, the Schematic Symbols must be found and placed but for the symbols to be of any use they must have PCB Footprints either already associated with them or assigned to them after they have been placed in the Schematic.
This document linked to below describes some of the issues around finding symbols and footprints and around associating footprints to symbols.
Note that all symbols and footprints saved to any library are automatically publicly available. This is true even for symbols and footprints saved from within Private and Team Projects.
The document then goes on to describe a procedure that guides the user to create high quality, well documented Schematic Symbols and their associated PCB Footprints which can be easily found and clearly identified by all other users.
Please see:
How to create findable Footprints and searchable Symbols
or:
How to create findable Footprints and searchable Symbols (web version)
#Skill#Hey guys this is my first time making a PCB board so I am not sure about whether or not mine is to the standards or not. In order for me, to my knowledge, to connect all of my components together, I had to make a few of the resistor and capacitor pads multi-layer instead of just top layer. Is this allowed and and does something like this actually work still? Sorry if this is a dumb question but in the PCB designer it looks like the pad has a hole in int when it is multi-layer which makes me think it is not acceptable to change the pads to multi-layer. Also if anyone has any suggestions or ideas for my circuit please let me know as well!
https://easyeda.com/ryanstjohn3/testpcb
** I see there is a clearance issue with two of my capacitors\, is this due to my traces or the actual components?
#PCB#I'm planning on building a guitar amp and i wanted to simulate the circuit but i have these errors i can't get rid off:
Here is my project : https://easyeda.com/alassaneg/guitar-amp
I don't have issues anymore when i remove "VolPROBE5".
Circuit: gooduntitled
Error on line 4 : v4 0 xu1_4 5 dc 1 0
unknown parameter (0)
Error on line 9 : r3 0 r3_2 volprobe3
unknown parameter (volprobe3)
errors/warnings in your design, please fix them if you need
errors/warnings in your design, please fix them if you need.
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000
Warning: r3: resistance to low, set to 1 mOhm
Warning: v1: no DC value, transient time 0 value used
Initial Transient Solution
--------------------------
Node Voltage
---- -------
xu1_1 5
xu1_4 -5
v1_1 1
xu1_3 0
xu1_9 0
r5_2 0
r3_2 0
xu1_10 0
volprobe4 0
v1#branch 0
v4#branch 0
v5#branch 0
No. of Data Rows : 738
Error(parse.c--checkvalid): volprobe3: no such vector.
ngspice-26 done
If someone could help with that, it would help me a lot.
Thank you.
#Simulation#





