Hello i am new to easyeda. But i have some experience with spice simulation.
I have tried to simulate a basic clipper for several days but with no success.Can somebody help me what am i doing wrong.
https://easyeda.com/editor#id=cafdab8b0db04704be912826ef9578b4
#Simulation#Hello.
I am new using Easyeda..
I have to use in my project GaN Transistor GS66516T, where i dont know how to get te schematic capture and the pcb layout.
The page of the product is:
https://gansystems.com/gan-transistors/GS66516T/#board
where i have the library for others programs but i dont know how to "convert" them to open on Easyeda
Kind Regards
Rui Moreira
Investigating the problem identified in my last post necessitated changes to component footprints in Schematic view and updates to the assiciated PCB. In the previous version of EasyEDA this presented no problems. However, in the latest version updated today, footprint changes (hole and pad size changes) are not carried over into the PCB consistently, and in any event are never reported as a change in the update dialogue. Because I have in some cases been editing standard EasyEDA package footprints, e.g. TO-220(TO-220-3) the edits became Personal. I checked that the component in the schematic was linked to the correct Personal PCB Lib footprint in each instance in the schematic, but clicked "Update" anyway. After changing all the TO-220 components, I updated the PCB, but the dialogue only showed changes to connections to GND (I don't have any, the ground plane being specified as EARTH for consistency with the mains PE (Protective Earth)) which I then have to reverse in Design Manager. It should be showing that the TO-220 components are to be updated. Nevertheless, upon checking the PCB, sometimes the hole size changes made would be present, sometimes not, and the update process would have to be repeated until they were. It would appear that the updates only take effect consistently and are presented in the dialogue if the component has been removed and replaced in the schematic, even though the effect in the schematic is the same regardless of whether it is updated or replaced. This is inconsistent and should be corrected.
#Feature Requests#It appears that there
is an error in the conversion between Inch, mil, and mm dimensions in
EasyEDA. Noting that the conversion factor was standardised in 1959
at 1inch = 2.540mm, errors in the third decimal place should be
avoidable if arithmetic precision is suitably matched to the number
of decimal places displayed, and appropriate rounding is used. Are
all calculations done in mil regardless of the unit of measure
selected and converted afterwards, or are calculations done, as they
should be, in the selected unit of measure?
This may be related to my previous post on DRC errors.
When checking the
Gerber PTH Drill sizes with Gerbv for my board I found that I had
nearly twice as many drill sizes as hole sizes. I therefore went back
to the board schematic and reviewed/ modified all the PCB footprints
(PCB Lib) and standardised on hole/pad sizes based loosely upon IPC
recommendations for lead clearance and relative pad size. This
resulted in 6 different hole sizes being used: 0.800mm, 0.899mm,
1.000mm, 1.100mm, 1.200mm and 1.300mm. Note the 0.899mm is the size
used for AXIAL-0.3 from EELib which i have used for all resistors, so
I used the same sized hole (0.899mm) for all components needing
0.9mm. However, the resulting Gerber shows additional drill size
requirements of 1.101mm for some of the 1.100mm, 1.201mm for some of
the 1.200mm and 1.301mm for all of the 1.300mm holes. Going back and
editing the footprint files to ensure that holes were defined to 3
decimal places (i.e. type 1.300 instead of 1.3) eliminated the
1.201mm and 1.301mm extraneous Gerber drill sizes, but NOT the
1.101mm.
Checking all the 1.1mm
holes on the EasyEDA PCB view showed them all indeed to be 1.100mm,
however the same board in Gerbv has them all as 1.101mm.
It is interesting to
note that the holes from AXIAL-0.3 and others set to 0.899mm in order
to standardise all come out at the preferred diameter in Gerber as
0.900mm.
Hello, when i place a Opamp like NE5532 in my schematic, how do i place the 2 internal opamp symbols that refer to each of the 2 opamps while maintaining one footprint?
When i select NE5532 in the library and place 2 of them, they are named U1.2 U2.2, when i now convert it to a PCB, its 2 sepperate IC's
How do i select the second opamp symbol to be the opamp2 in the same U1 IC?
schematic:
https://i.imgur.com/mOzf8eW.png
pcb:
https://i.imgur.com/QEkdjGw.png
EDIT figured it out
double click the subpart in the library window, dont click Place.
#Feature Requests#


In the above picture you can see those areas highlighted in red. Thank you for your support and keep up the great work.


