Help Please

Hi,can someone please help me? This is what keeps showing up.

Circuit: gooduntitled

Error on line 4 : sw1 r13_1 r14_2 sw_sw1 off
Unable to find definition of model - default assumed

errors/warnings in your design, please fix them if you need

errors/warnings in your design, please fix them if you need.
Reducing trtol to 1 for xspice 'A' devices
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000

Warning: singular matrix: check nodes led1#branch and led1#branch

Note: Starting dynamic gmin stepping
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Warning: singular matrix: check nodes led1#branch and led1#branch

Warning: Dynamic gmin stepping failed
Note: Starting source stepping
Warning: singular matrix: check nodes led1#branch and led1#branch

Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful source step
Warning: singular matrix: check nodes led1#branch and led1#branch

Warning: singular matrix: check nodes led1#branch and led1#branch

Warning: source stepping failed

#Simulation#
Circuit Design
SCR shut down circuit

I want to create a SCR shut down circuit, but it is not running "error: does not have a probe"

I googled it but I couldn't find the answer or atleast I didn't understand it since English is not my native language....

can someone help me out with this circuit:

https://easyeda.com/editor#id=d313a443978d464e89c5b76833dee979

I want to see what the current through the resistor in the end is, therefore I want to trigger the first SCR lets say after 5 ms and then to shut it down trigger the second SCR which is above it after 10 ms, then I want to see if the second SCR will be shut down because the negative source of the capacitor shuts it down and what voltage I will have, because my task is to create a circuit at which the capacitor voltage will not become negative

#Schematic#
Circuit Design
I am told that website has bug when ordering PCBs with no solution! Tried 3 times!!!

BUG

Concise problem statement:

I have tried to order a PCB design 3 times for over a week and each time I get:

It seems our website has some wrong. Sorry for this. n fact, each
order only includes one chance of $2. $2 is just availble for total
10 panels (10 individual boards) and without any paneled. If 160
individual boards, maybe you have to pay the extra. Pls you check and
confirm. Thanks for your understanding.

Best regards Sophie

My most recent is order pvsOa8642

I don't care about paying extra (within reason) but I need these boards ordered and
nobody has told me how to proceed.

I already ordered stencils so I absolutely need them in 4x4 panels with Edge Rails.

I keep asking how to order or fix this problem, but I get the same reply each time!

Steps to reproduce bug:

  1. Design a board and order it panelized where the total size of the panel is < 10cmx10cm

  2. My board is 20mmx20mm so a 4x4 panel is 8cmx8cm, I then order 10 panels.

  3. There is a sale listed on the order page

Results:

  1. Cart shows $2. ($14.20 after shipping and handling)

  2. After checking out Sophie tells me that the website has a bug.

  3. I ask how I am supposed to order.

  4. I get told the website has a bug and it won't be fixed anytime soon.

  5. wait a few days, try again...

  6. same email, same question

Expected results:

I order boards online, pay for them, they get made and shipped to me.

Please turn off the stupid $2 sale!!! I am not the only one with this problem.

Browser:

Chrome

#Bug Reports#
Bug Reports