Circuit Design
PCB review possibly? extreme noob

So I just got into this website as other websites such as circuits.io are not as advanced or easy to use as this one. Anyway I am going to be doing home automation and I can do it without a PCB and i made up a prototype that works however it looks terrible. hence me making a PCB.
I was wondering if someone could look over it and see if I did anything major mistake wise. I am sure there is some. I know enough to be able to put existing components in.
I can explain every part if need be
here it is
https://easyeda.com/bizit524/ESP-pOI0UEyiE

Here is a breakdown of what components I have
ESP01 which is powered by an hlk pm01. This hlkpm01 has mains screw terminals and goes first to a 5v to 3.3 v step down converter. There is a bypass jumper that completely bypasses that circuit and powers the ESP if I ever choose to buy a hlkpm03 which is just straight 3.3v instead of 5 (same footprint).

There is a program header which I plug in a UART usb programmer which supplied 3.3v ground, tx and rx to the ESP. To get it to flash I have to bring pin2 high and pin0 low. There are two jumpers there to do that.

Since an ESP01 only has 2 GPIO pins it will control 2 of 3 things on the board I have. I have a dht22 which is a temp sensor with a pull up resistor that goes to GPIO2 OR if i dont want a temp sensor it can be left blank and power a 5v relay which is activated by a 2n2222a transistor. There is a diode across each relay and a resistor going from GPIO pin to transistor.

Relay two is the same thing except its dedicated both have screw terminals.

Have I screwed up anything major??? I would love your input

#PCB#
Circuit Design
Waveform not displayed after transient simulation

Hi, this is a SPICE newbie question.

I used a non-inverter amplifier circuit (with LM741) to play with SPICE simulation in EasyEDA: https://easyeda.com/editor#id=7mIC8NHBT

When I launch a transient sim (be it with a 1V DC input or with a sine), I'm quite happy with the initial conditions shown in the results (at least regarding the nodes I have named myself), I'm reasonably happy with the 1012 data rows it claims, but I'm a bit frustrated by the absence of a waveform. What have I done wrong this time?

My simulation results (1V DC input):

Circuit: untitled

Reducing trtol to 1 for xspice 'A' devices
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000

Initial Transient Solution
--------------------------

Node                                   Voltage
----                                   -------
xu2.11                                 14.9602
xu2.12                                 14.9601
xu2.6                             -0.000858624
xu2.7                                  11.7991
vs                                     9.99926
xu2.53                                    12.4
xu2.54                                   -12.4
xu2.90                                 11.9991
xu2.91                                      25
xu2.92                                     -25
-vee                                       -15
vcc                                         15
xu2.99                                       0
xu2.10                                0.402537
v-                                     0.99989
xu2.13                                0.416472
v+                                     0.99996
xu2.14                                0.416497
xu2.9                                        0
xu2.8                                  11.7991
e                                            1
h.xu2.hlim#branch                 -2.39982e-11
v.xu2.vlim#branch                    0.0119991
v1#branch                         -8.02178e-08
v3#branch                          -0.00166656
v4#branch                           -0.0016667
v.xu2.vln#branch                  -3.69999e-11
v.xu2.vlp#branch                  -1.30017e-11
v.xu2.ve#branch                    2.24001e-11
v.xu2.vc#branch                    2.40154e-12
v.xu2.vb#branch                   -8.58624e-09
a$poly$e.xu2.egnd#branch_1_0        -0.0119991

No. of Data Rows : 1008
ngspice-26 done

Thanks in advance.

#Simulation#
Circuit Design