Please help with my first ESP32 S3 PCB (hooking up USB and transceiver properly)

This is my first time designing a PCB, so I’m not 100% confident everything is correct and would really appreciate any feedback before I send it to JLCPCB for assembly.

The board uses an ESP32-S3-WROOM-1-N4R2 module and is powered via USB-C. It includes:

  • Two WS2812B LED strips, each with 6 LEDs, powered by 5V and controlled via a single GPIO pin.

  • A surface-mounted hall effect sensor for magnetic trigger detection.

  • A 433 MHz RF transceiver, controlled by GPIO to send remote alerts.

  • A momentary push button (manually soldered) for user input (mode switching or shutdown).

  • Supporting components:

    • Decoupling capacitors for power stability

    • Pull-up resistors for boot/enable pins

    • Voltage filtering caps for RF and LED power

I'm using the USB-C port for both power and programming. I struggled a bit with configuring it, especially to ensure it safely powers both the ESP32 and LEDs. The ESP32 runs on 3.3V, while the WS2812B LED strips require 5V. My battery pack outputs 3.3V, but USB from my PC provides 5V, so managing the power distribution and regulation between components has been a challenge.

Also, I’m not confident that I hooked up the crystal correctly for the 433 MHz transceiver. Any advice on whether that looks right or if I should change anything there would be really helpful.

The LED strips and button will be soldered by me—everything else should be SMT assembled by JLCPCB.

I'm including a picture of my schematic and a few resources that I used as references.

Any feedback on routing, component selection, power handling, or layout best practices would be hugely appreciated. Thanks!

#PCB#
Circuit Design
Mini High-Voltage Arc Generator (Taser Project for Educational Purposes)

📦 Project Description:

This project is a portable high-voltage arc generator, often referred to as a "taser" for educational and research demonstrations. It uses a DC 3V–6V to 400kV boost converter to create visible electrical arcs, simulating how high-voltage discharge systems work.


⚠️ Disclaimer:

This device is intended only for educational, testing, or scientific display purposes. It should not be used on humans or animals, as it can be dangerous and potentially illegal depending on your local laws. Use at your own risk.


🔋 Hardware Components:

  • 1x 3.7V 2200mAh Li-ion Battery (protected)

  • 1x Charging & Protection Module (Type-C with boost output)

  • 2x DC 3V–6V to 400kV Boost Step-Up High Voltage Generator Modules

  • Wiring, heat shrink, and solder

  • 3D printed or laser-cut housing (optional for safety)


🔌 Circuit Overview:

  1. Battery is connected to the charging/protection module:

    • BAT+ → Battery Red (Positive)

    • BAT− → Battery Black (Negative)

  2. Output from module powers the high-voltage generator(s):

    • OUT+ → Red wire of HV module

    • OUT− → Black wire of HV module

  3. A switch can be added between OUT+ and the HV input for safe toggling.


🛠️ Tools Used:

  • Soldering Iron

  • Flux + Solder

  • Wire cutters/strippers

  • Multimeter (for voltage testing)

  • Safety glasses and insulated gloves

🧠 What I Learned:

  • Basics of step-up converters and high-voltage discharge

  • Importance of protection circuits for Li-ion batteries

  • Safe handling of high-voltage circuits

  • How to integrate boost modules with regulated battery packs


✅ Next Steps:

  • Add a 3D printed protective shell

  • Integrate an on/off toggle and arc trigger

  • Expand to controlled pulse mode using MOSFETs

#Project#
Projects
LED matrices from elevator panel

Hello!

As part of my working method in which I often use recovered components, I present to you this panel with 5x8 LED matrices recovered from an elevator panel. It is a PCB built after the model of the 8x32 with 8x8 matrices only that mine are larger (37.6mm*23.5mm). In addition to the LED matrices we also find MAX7219 ICs using for what else than as drivers, some capacitors and SMD resistors.

The first attempt was a homemade PCB (toner transfer, iron, a lot of work 🙆‍♂️), after many attempts (It's not easy to make double layers PCB at home), and which ended up degrading, I started with 4 matrices but I need to add one more because it has to do with the font of the displayed text (depends on the software), or better with 5 pieces. So I sign up for this activity also for the opportunity to improve my project.

The panel can be used with an Arduino board or other and the software libraries MD_Parola and MD_MAX72XX from Arduino IDE offer us enough help. I also had to make some SW adjustments because the situation is a little different, characters at a different width. You can build a digital clock, thermometer+hygrometer, or whatever else you want.

The result is a big PCB, two layers, 196mm*70mm and a little heavy but it's okay for me. At some point I'll have to find a better way to store it, after I finish the project (a big clock with an Arduino board) I'll build a proper case.

You can see a moment with this panel (the old version):
https://youtube.com/shorts/_MsfRvQ6Yj0?feature=share
old pcb 1
old pcb 2

And the new one:
Top side PCB

Bottom side PCB

I can't add many more details because it's more of the kind of project that speaks for itself, it is something that can only be used for displaying a text.

Do you like it? 😁

Thank you and have a nice day!

#Project#

Projects