Library Search Result Difference Between Standard and Pro

I have designed a PCB in Online Standard and I am now creating the same design in Online Pro to compare the two versions of Easy EDA.

https://oshwlab.com/sk8board/esp32-elrs-receiver

My Standard design uses a library part that is titled IFLIGHT MICRO BEC. There are many user contributed parts to choose from in the Standard Library. I found a user contributed part by Jim Kazmer that includes the schematic, footprint, and 3D model. When I search using the Pro Library, I cannot find this same part. In fact, many of the user contributed parts are not available in the Pro Library.

Why are the search results very limited in the Online Pro version of Easy EDA compared to the Online Standard Version?

#Library#
Circuit Design
Component pins via'ed to nets that have planeZone layers pointlessly also autoroute on a signal layer

I created a simple schematic with parts from the common library [component details unimportant]:

  • a 2-pin connector
  • a resistor

 

I exported this to a 4-layer board:

 

with this setup:

[There's a bug that automatically assigns the pour on the VCC layer to net GND; I manually corrected that.]

 

This autoroutes as expected, two tracks on the top layer:

 

 

But ...

 

I don't want to clutter the top signal layer with GND and VCC tracks. It's the whole reason that I created those inner planes.

 

So I created blind via types in DRC: TV is top to VCC, and TG is top to GND:

Then I drop vias next to the GND and VCC pins of R1, change their nets appropriately, and convert them to the appropriate blind vias.

 

At this point, there are ratlines from R1's pads to the blind vias, as I guess I expected:

Problem 1: Autorouting this to draw the two tiny tracks from R1 to the vias hangs forever [ok... until I run out of patience minutes later...].

 

Problem 2: If I manually route those two tracks:

[note that the ratlines went away, as expected], and autoroute [i.e., to autoroute the other components that I'd also add in a real project], it finishes, but it redraws the same two now-redundant tracks across the signal layer as before, even though they are not needed [or wanted]:

Why?  Can I avoid this? It's why I put in the planes and vias in in the first place: to avoid hogging real estate and setting myself up for failed routing on the top layer.

 

Thanks!

 

...R

#PCB#
Circuit Design
EasyEDA PRO does not Center Via on Pad

Hi –

 

I have been using the Standard version for the last 3-4 years but have switched over to try the PRO version, especially since the latest design is very large and Standard cannot keep up.

 

There are a few things in the Pro version that are yet not working, however I know you are still working out things and adding features.

 

There is one feature that is crucial from day one that I cannot seem to get working.

 

I am using the Client version on Windows 10 and using the latest version 2.1.51.

 

When trying to snap a Via to the center of a PAD, it does not snap to the center IF you grab a via that is already located on your canvas..

If you click the via tool and then move your mouse over the pad, it will snap to the center of the pad. But that is the only way it will do it. Lets say you have replaced your compoenent from a 0603 size to a 0805 and you are using via-in-pad for your VCC and GND connections. As the footprint changed, you need to drah the VCC and GND vias to the new locations of the pads of the larger 0805 footprint. That does not work, it will not snap.

I have attached a short video that display the issue and it also show the settings for the EasyEDA PRO application which clearly shows that I have selected to snap to center of pad.

Correction, apperently you cannot add a video, which is too bad as it shows the via circling the pad without ever snapping to it.

In the EasyEDA STANDARD version, it always snaps to the center of any pad, by default.

Please instead see the 2 images showing the settings and the pad and via, which are of the same net.

 

 

 

Is this something you are aware of and will fix? Or, am I doing something wrong?

This feature is one of the most important in a CAD software so I would assume many people would have complained if this was an ongoing issue.

 

Can you please give some advise on this?

 

Thanks,

 

Michael

#PCB#
Circuit Design