This Bug Report is also directly related to this Feature Request:
https://easyeda.com/forum/topic/Please-reinstate-the-DETACH-function-8b6fe2d37d6c4f8f8a4071055c3879af
Some months ago I successfully created a spice symbol for the V2164 quad VCA as a 5 sub-part symbol:

I have successfully used this symbol both for simulation and non-simulation schematics for 2 differnt designs and from which I have produced PCB designs with no issues.
(Please note that Ihere are also other non-spice symbols for the V2164 but they not the one's that I am talking about here.)
As noted in the Feature Request above, if I select, cut and paste a sub part, although the sub-part number stays the same, the main device prefix number is changed to a new number.
- I then find that for the V2164 spice symbol I cannot change the main device prefix number of the sub part back to what it was originally.
- I think this behaviour has changed within the last version or maybe two versions of EasyEDA because I have previously been able to edit their prefixes.
There is no warning that the part already exists: the number just does not change.
Saving and refreshing does not correct this problem.
Cut or copy and pasting the sub part again does not correct this problem.
Deleting and then replacing the sub-part from the library does not correct this problem.
The only way I have found to correct the problem is to edit the main device prefix number in the JSON File Source for the schematic.
#Bug Reports#Hi all
I've run into a problem with the autorouter. I'm using a local
installation of the autorouter (running onWindows 10) and when
running the autorouter in local mode (or Cloud) it appears to be hanging. However,
when I look at the autorouter log file, I can see that it stops as soon
as it starts, writing only the following messages.
-------------Connection established-----------
Start routing...
Routing
-------------Connection closed---------------
At the beginning the auto router worked perfectly fine, but after some changes it suddenly stopped. Unfortunately I cannot pin it to a component.
I already tried the suggestions given in Readme.txt and EasyEDA Tutorial - as far as I understand them - but it didn't work.
My project can be found at https://oshwlab.com/chruetli/rs-422-usb-switch_copy
Hello,
I am new to EasyEDA and I'm using the 6.4.17 desktop client on Windows.
I followed the tutorial on version control (004 Version Control - YouTube) and after creating a new version,
I can't save it to the cloud and I get this error "Save fail, project version doesn't match!"
I tried in the web browser and there it works perfectly.
Thanks
in accordance with https://docs.easyeda.com/en/SchematicLib/SchLib-Subparts/, I added subparts for a multi-gate digital logic chip. The tutorial says "double click on each sub part in turn to modify the Pin Name and Number attributes." But when I do that, I just get the entire part on my cursor for placement on the schematic. What am I doing wrong? I want to configure the subpart diagram, pin numbers and pin names so that I can place individual subparts on the schematic (e.g., flipflops, AND gates, etc) showing the pin numbers and pin names that I assign.
#Schematic#Hi guys!
I came here a while back for help arranging a PCB which had an integrated Arduino pro micro 5v. This was so I didn't have to solder on an actual pro micro onto my PCB!
I took the schematic of a pro micro 5v and I merged that with my current schematic which was really simple a few switches and an encoder. Now I did the PCB design and got everything joined up and in place and bit the bullet and had a few made!
However today I received them, soldered on my USB-C port but it is not being picked up in windows, or if it does it says there was a problem with the device! One thing to note is that LED1 does light up solid, and shorting the reset pads does disconnect and reconnect sound in windows but it still is not recognised.
Now in terms of the USB-C, on the schematic I used a SHOU HAN C668624, but the actual part I soldered on was a DX07S016JA1R1500 but the pinout seemed to be the same?
Now if that port was not the issue I cam hoping someone with a bit more knowledge could spot the mistake I have made in my schematic D:
https://oshwlab.com/AKiwi92/macro-pcb_copy
Looking for a little direction on what I have done wrong! Hoping if there's something connected wrong I can cut traces / jump something to get it debugged and working!
Thanks!
Ash
LAN.PNG (273.57 KiB) Viewed 2 times
Hi,
I have designed and assembled a board that uses LAN8720A and ESP32 to create a POE setup. I broke it up into 3 sections for testing and verification; uC w/PHY, POE PD Controller.
But i test without POE in this case I'm currently only testing the uC/PHY isolated from everything else and providing power through USB dropping down to 3.3 using a linear reg. !!
The LAN8720A has communication with the esp32 but not with the network. i.e. the phy is configured without error and even detects when the LAN cable is connected and disconnected but it never gets an IP address and/or connect to MQTT server !!
I have a waveshare breakout board for the LAN8720A for which I followed sautter's guide and it works well. https://sautter.com/blog/ethernet-on-es ... ng-lan8720
I used the waveshare schematic as my starting point https://www.waveshare.com/w/upload/0/08 ... ematic.pdf
When I compare schematics I don't see anything glaring that would seem to indicate improper connection so my guess is my issue is with layout.
i use transformers inside an RJ45 jack : https://docs.rs-online.com/90ab/0900766b815b818d.pdf
i have 4 layer pcb stackup 1.6mm (signal-GND-POWER-SIGNAL) with Impedance checked construction with EasyEDA : impedence diff 100R :
-track space 4.70 mil
-track with 6.00 mil
-track height 1.36 mil
-isolation heigth 7.08 mil
-dielectic cst FR4 4.300
Let me know if you see anything in the schematic or layout that might an issue.
Patiently waiting for your input.
Thanks!








