Problems with VCC vs +5V netflags in simulations.

In answering this topic:
https://easyeda.com/forum/topic/voltage-source-simulation-pcb-implementation-dabdd889176c4cb2a7de722c3031bb9e
it has been found that there are problems with the internal voltage sources that EasyEDA auto-assigns to simulations when netflags such as VCC, +5V are assigned to nets.

  • This causes this simulation to be produce rubbish results which was not noticed by the user as they are a self-confessed novice.

It looks like as long as any other explicitly placed voltage source in the sim does not share a common net (other than ground or 0) with an EasyEDA auto-assigned voltage source then all the voltage sources are netlisted correctly.
However, if any other explicitly placed voltage source in the sim does share a common net (other than ground or 0) with an EasyEDA auto-assigned voltage source then some or all the voltage sources are not netlisted correctly.
Sheets Sheet_1 to Sheet_4 and Sheet_6 and Sheet_7 in this project:

https://oshwlab.com/andyfierman/vcc-vs-5v-netflag-problem
demonstrate this issue by pasting the netlists into the schematics as text.

  • Until this issue has been resolved it is recommended that all required voltage sources MUST be placed explicitly in the schematic as shown in Sheet_5 to correctly netlist all voltage sources. Voltage sources can then be connected to other nodes using netflags without the netflags invoking additional EasyEDA auto-assigned voltage sources.
#Bug Reports#
Bug Reports
voltage source simulation/pcb implementation

Hello,
Here the sketch of a circuit I have implemented and which simulation gave me exactly the result I wanted.
https://easyeda.com/editor#mode=sim,id=fb3873960883413b855ad2eb1bfb2f15
I have ordered the PCB accordingly (waiting now for it to arrive), placing an extra pin header footprint in order to substitute all my external connection (and dividing the circuit at the point of Probe2 to insert another part) . Anyway, this is what I wanted to simulate and I will have a sin wave generated by Arduino as an input signal (V1). But I am not sure about how to properly substituting V2!? If for example I just connect a battery, what would be the difference with +/-5V? Because when simulating it made all the difference!
[If the question will sound too easy to you, I hope you understand that I am new of the world of PCB and implementing electronic circuits, apologies in advance].

Regards

#Simulation#
Circuit Design
Bad user experience on PCB order

Hi,
after a while, I ordered again 2 boards for a personal project:
Y21-2253036A and Y20-2253036.

It is a simple led board with size 30mm x 50mm.

Since it is small I tried to panelize it to reach a size of 90x100 (3x2).

Experience 1:
At this point, easyeda report it as 107mm instead of 100mm. So I removed the second row. Now it is 57mm height (why 7mm more?)

Experience 2:
Once ordered I got the message from support that the board is only 50mm and that a v-cut is not possible.
- Why can't you detect it during the order process? Or directly in EasyEda?
- Why 50mm when it was reported 57mm in EasyEda?

Experience 3:
I added a 10mm border on each side. Now it was 70mm (77mm for EasyEda) - Failed again! It is less than 70mm now for the support!

I decided to add 15mm to the border, to reach 80mm (87mm for EasyEda).

Experience 4:
Now the board is 90x80mm and was able to submit it. But unfortunately the price is not for a panelized panel. They ask some more money (for each submitted board - +0.50$ paypal fee for each payment!).

I don't want cry for the price... As it is really low.

But on the last order:
- I was able to make a single order for the boards and for the components. This is not possible anymore.
- I was able to order a 2x2 panelized board 50mmx50mm without extra charges.

Now, you accept a panelized board (it is still less than 100x100mm) and aks more money once it was submitted?
It doesn't give a good user experience and is dishonest as you can detect it on EasyEda (but EasyEda reports 5$, not 11$)!

Hope you can solve it, as with this trick (increase the price once paid) will let choose other services one day.

Best regards,
Tiger54

#PCB#
Circuit Design
First time order understanding panel ordering

A couple of pieces of information I think might be relevant.
I'm doing a small scale project for myself, I lack the skill to do surface mount work but can handle through hole things.
My intent is to use JLCPCB to print the boards and do the SMD mounting and then do the through hole stuff myself.  I want a printed board rather than a perf board for compactness and reliability.  I hope to 3d print an enclosure to put the PCB in.
When reviewing the options for placing an order I saw a couple of options that I understood but didn't fully understand the implications.
It looks like I can design a single panel and then have that created multiple times.  Or I can design a single panel with sub-panels that I break apart myself.
My project has a central power board, and remote connector boards.  Each central board could theoretically use as many as 12 connector boards or as few as 3.
When placing the order I saw an option that identified if I would be printing different layouts.
Is there a method that would be less expensive/complex than another?
The way I see it I could order a board that has everything on it and break apart into multiple little boards.
Or I could order the minimum number(5 I think) of boards of each board.
Or something in the middle.
Given my desire to have all the surface mounting done by JLCPCB, and the various extra costs associated with that, which method is preferred?
I could play around with it trying all the various configurations but I thought someone might know the answer off-hand.
Thank you

#PCB#
PCB
JLCPCB does not recognize BOM and CPL export from EasyEDA when adding SMT service to order

If you are having JLCPCB perform SMT services to build your PCB and place SMD parts on the board, the native exports of the BOM and the CPL files will not work.

When uploading the BOM and CPL files, that have been exported from EasyEDA, the JLCPCB website reports "there is no smd part on top side, please go back to re-upload files or choose to assemble the other side". The files exported from EasyEDA are designated as "Unicode Text (*.txt) and are TAB delimited, but have the .csv file extension. JLCPCB will accept this file type as valid, however once you continue with the build process, the JLCPCB website will fail with the above error message.

NATIVE EasyEDA BOM Export
ID Name Designator Footprint Quantity Manufacturer Part Manufacturer Supplier Supplier Part JLCPCB SMD LCSC Assembly _Price
"36" "12V" "GLED1" "LED0603-RD" "1" "TJ-S1608SW6TGLC2G-A5" "TOGIALED" "LCSC" "C192316" "" "Yes" ""

The solution is to export the BOM and CPL files as you normally would from EasyEDA and store those to your local PC. Then, open the files in EXCEL and perform a "Save As", making sure to select "CSV (Comma delimited) (*.csv)" as the file type. After performing this task, JLCPCB website will be able to upload and process both the BOM and the CPL files and you will be able to continue the build process and get your PCB manufactured with SMD devices.

I also find it necessary to reduce the output of the native BOM export, so it makes it easier to identify the parts that are actually going to be placed on the board since JLCPCB SMT services does not place certain parts.

MODIFIED BOM Export
Name,Designator,Quantity,Manufacturer Part,Supplier Part
12V,GLED1,1,TJ-S1608SW6TGLC2G-A5,C192316

It would be nice if the exports for BOM and CPL in EasyEDA had an option for which file type should be exported and that the BOM export would allow you to preselect which parts should be exported, rather than just ALL PARTS.




#Bug Reports#
Bug Reports