Mouse-Bites in EasyEDA

I know how to do V-Panel cutting in EasyEDA (see here).

However, I'd like to do Mouse-Bites as my PCB shape doesn't work with V-Panel cutting.

Is this possible? If so, how? And is the PCB still suitable for SMT assembly?

#PCB#
Circuit Design
Misaligned drill holes: problem with EasyEDA or gerbv 2.7.0?

A very simple PCB with a single through hole pad.

https://oshwlab.com/project/publish/b3fff9808c9641bc8ced01e6744323c9
EasyEDA PCB view:

image.png

Gerbers viewed in gerbv 2.7.0 show misaligned drill hole:

image.png

Same Gerber files at gerber-viewer.com show correct drill hole location:

image.png

Note that this may be related to this topic:

https://easyeda.com/forum/topic/Incorrect-Drill-Holes-Position-0cd73ab552834d8ca510da0e94898d51

#Bug Reports#
Bug Reports
12V Automotive Timer Simulation Difficulties

Hello everyone,
I'm having some difficulty with my simulation. I've read through the documentation (admittedly, not ALL of it) and have made the changes recommended to get the project to simulate. I've worked through a few examples too.

So, this is an old timer used in public safety vehicles. It is no longer in production. Some coworkers have hinted for some time that they'd like to be able to recreate it because it's been such a solid device for so long and they don't want to move to a different device. I have downtime, so I'm taking it on. This is good practice for me because I've never been good at circuits and want to get better. 
 
The DIP switches on the bottom right are intended to change how long the device stays "on", allowing equipment in the vehicle to remain powered. R12 and R13 were added by me after reading through the tutorials. The battery and igniton are both 12V, but the ignition is the trigger so I changed it to a pulse function. I tried changing the battery to a pulse too, just to see and didn't see much change. R9 is the load I created to see if the relay was working. It's supposed to be a T9AS1d12 12V automotive relay from Potter and Brumfield. I was able to find that model in the spice library that, according to EasyEDA's documentation had a spice model but it didn't seem to work, so I changed it to the current one. Which also doesn't work. I had R9 connected to pin 87 and moved it to 87A when I didn't get an output, which I still don't on 87A. 
 
I'm confident my tracing is correct and I've done my best on components. What I'd like to do is simulate the circuit and see if modifying the switch resistors, capacitors and IC will give a more accurate time range. For example, switch #5 on the device is labeled as "1 to 3 hours" of run time. That seems like a wide margin. The voltage probe C1 shows a ramp up to 12V which is what I would expect, but if I close a switch the voltage is very low, which is what I would expect after some time, but there aren't any transients or anything that shows me info up until that point. I also tried a voltage controlled current switch which I gave 8GV at C1 so that's definitely not correct. 
 
I don't know if I can even accomplish this in EasyEDA. We use the "1-3 hours" selection on the device and taking the simulation out that long may be beyond what EasyEDA is capable of? I think the problem is in my voltage sources. I've been playing with it for a few days and I'm at the point where I need some guidance. Can anyone help me?

https://easyeda.com/editor#mode=sim,id=1443b45e818f4012b551070afced3451



https://easyeda.com/Dkraemer/timer

#Simulation#
Circuit Design
How to create separate moveable subparts in schematic

I am in the middle of making a big schematic for a pcb. On there I have multiple parts that I'd like to 'split' so I can place one part on the left of the schematic, and the other part somewhere else. I have looked at the tutorial about creating sub-parts which seems to be what I am looking for but when I follow the tutorial I cant seem to get the parts 'seperate'. I still get the parts together and unable to move sepearetly from eachother. I thought I might had to make the subpart .1 one part of the schematic, and .2 the second part etc but this seemed to delete the part I wasn't using.

#Schematic#
Circuit Design