I completed my first PCB. But I really knew nothing when I started. How do I get someone to review what I made and tell me if it can be created or if I have problems? It began as a copy from a PCB by HowToMechatronics, but I ended up completely revamping it (to use a Nano). I want to get it printed, but it needs a critical review first. Can anybody help? Also, I don't know how to publish it so people can review it. And once people tell me it looks okay, how do I get it created?
- Did I route something wrong? I noticed that the original from HowToMechatronics did not route the GND lines. I didn't understand why, so I routed them.
- Are any of the lines too close?
- I intend to power it though the USB port on the Arduino Nano using a Cell phone battery pack. So, no switch...just unplug.
P.S. This site ROCKS! Needs better learning tools and help information, but functionality of the site is excellent!
P.P.S - I think I made the project public. https://easyeda.com/jimkrug/arduino-radio-controller I want "Using Arduino Nano" reviewed. Feel free to review the other one, but GND is not routed and I don't know how it would work. Plus I think RobotDYN's board does not work properly with MISO and MOSI. I have 3 boards...none work. Nano worked on the first try.
#PCB#I have been using these 2.4ghz transmitter previously in my arduino projects, with good success.
One of my latest PCB design incorporates the schematic of the chip used on these boards. It is working but I've narrowed an issue down to the pcb antenna, and the manufacturing of that. Basically I'm having intermittent signal loss and other weak signal artefacts.
My question is, knowing that certain factors of the radio signal and the 'ideal' antenna will depend on the final casing and other components, how do I make sure I can get the trace impedance to be 50 ohms? THis is required by the chip manufacturer.
Assuming the microstrip impedance is the way to calculate this (I used this one https://www.eeweb.com/tools/microstrip-impedance) for a 'standard' board, 1.6mm thickness, 1oz trace thickness and substrate dielectric of 4 (which I believe is FR4) I get a trace thickness of 3.2mm. However, the PCB on most of these off the shelf transmitters (they are around 1-1.1mm thick) have antenna traces of 1mm width.
I am puzzled as to which is wrong here. Based on the info that I know, should I go with the 3.2 mm wide trace antenna? Or should I rather 'copy' the layout of these existing boards, even though I cannot know the trace thickness and thus my information to calculate their exact impedance is incomplete?
Hello all,
I've just started discovering EasyEDA with a simple schematics (a DC source, a resistor and ground). I would like to use the simulation tool so I added a voltage probe and I would expect to measure the voltage of the source (+5VDC) (see below).
https://easyeda.com/editor#mode=sim,id=c32dc1bde9704e6b84f0aa3a89f9300c
No signal appears in the simulation window. What am I doing wrong ?
Thank you,
Philippe


The API documentation does not explain how to delete a shape: https://docs.easyeda.com/en/API/EasyEDA-API/index.html#Examples
In fact, it says this:
Delete Shapes
Removing shapes by follow code
Except, there is no code example!
In my case, I need to delete a track. I have tried an educated guess, such as:
api('deleteShape', {id:'gge13'})
I've also tried just setting the shape to have no points, as in:
api('updateShape', {
"shapeType": "TRACK",
"jsonCache": {
"gId": t2.gId,
"pointArr": []
}
});
The script I'm writing ought to be very handy for a lot of people. When you're designing and redesigning a board, often your tracks get subdivided. Then when you try and move things around, only part of the track moves; you have to move each subpart and delete any bits that are hanging on. The script does two things:
- It looks for pairs of tracks that have the same net, layer, and width, and where the start/end of one is also the start/end of the other. It combines them into a single track.
- Within any track, it looks for triplets of points (a,b,c) that are in line (ie: slope(a,b) == slope(b,c)) and replaces them with the pair (a,c), simplifying the track.
I have it completely working except for deleting the redundant track.
Much obliged for any help that can be provided.
#Bug Reports#I've created footprint, saved it, exited EasyEDA, run EasyEDA again and now can not place or edit this footprint because of "SVG parsing error".
It is https://easyeda.com/component/fb1bab1519af41c2b670abd08b880352
Hi,
Please can you help me.
I have DRC Clearance error even after making changes from 4 to 6 layers.
I tried to change size of Clearance in "Auto Router Config", and "Design rules", but nothing changes.
What happend?
Project link: https://easyeda.com/stanislav.ganna/snes-repro-big-pcb-with-battery-v2






Where do i put the speaker Where do i put the battery 
