Make TopAssembly & BottomAssembly dependent on layer (top/bot) on which component is placed

Hello,

It's not very clear what is the purpose of TopAssembly & BottomAssembly layers.  These happen to be just extra documentation layers.  The "TopAssembly"-layer doesn't seem to be related in any way to components on top.  The same holds for "BottomAssembly" and components on bottom.  These two layers might as well have been called "DocumentationX" & "DocumentionY".

More relevant behavior would be that these layers would be related to the components, just like"TopSilkLayer" & "BottomSilkLayer" are. e.g. When "TopSilk"-primitives are added in the PCB-footprint of a component (PCB Libs), swapping the component from top to bottom on a PCB, transforms pads on "topLayer" to pads on "bottomLayer", "TopSilkLayer" primitives to "BotSilkLayer" primitives.  Also the reference designator swaps from "TopSilkLayer" to "BottomSilkLayer" and text will become mirrored.  This is expected behavior.

When "TopAssembly" primitives are added to PCB Libs, moving such a component to the other side of the PCB, nothing happens with "TopAssembly" primitives.  They remain in "TopAssembly", although that component could now well be on bottom side of the PCB.  They behave like the documentation layer, which is not related to top or bottom.

I expect that "TopAssembly" and "BottomAssembly" would behave like "TopSilkLayer" & "BottomSilkLayer".

The use case is that people sometimes want to add primitives to components that should be visible on the assembly drawing (for which TopAssembly & BottomAssembly could then be used).  But they don't want those primitives be visible on the silkscreen.

An example of such usage can be found here.  The outline and polarity marking of the LED and switch should be visible on the assembly drawing, but not on the silkscreen of the PCB.

Regards,

Christoph

#Feature Requests#
Feature Requests
Error runnging the simulation please take a look and guide me

This is my test project for which I am trying a transient simulation:
https://easyeda.com/editor#id=|0aba11fae8a34a039ccdb860076db290

I used these settings:   Max Timestep: 10u, Stop time: 4m, StartTime: 0

And got the following errors can anybody help me with finding what causes this please :

Circuit: gooduntitled

Doing analysis at TEMP = 27.000000 and TNOM = 27.000000

Warning: v1: no DC value, transient time 0 value used
Warning: singular matrix:  check nodes gnd and gnd

Note: Starting dynamic gmin stepping
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Warning: singular matrix:  check nodes gnd and gnd

Warning: Dynamic gmin stepping failed
Note: Starting source stepping
Warning: singular matrix:  check nodes gnd and gnd

Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful gmin step
Note: One successful source step
Warning: singular matrix:  check nodes gnd and gnd

Warning: singular matrix:  check nodes gnd and gnd

Warning: source stepping failed

Transient solution failed -

Last Node Voltages
------------------

Node                                   Last Voltage        Previous Iter
----                                   ------------        -------------
input                                             0                    0
output                                            0                    0
r4_1                                              0                    0
q2_3                                              0                    0
vcc                                               0                    0
c3_2                                              0                    0
r1_1                                              0                    0
c3_1                                              0                    0
c1_2                                              0                    0
gnd                                               0                    0
v1#branch                                         0                    0

doAnalyses: iteration limit reached

tran simulation(s) aborted
Error(parse.c--checkvalid): input: no such vector.
ngspice-26 done

#Simulation#
Circuit Design
Can I simulate an opto-coupler?

Hi,
I'm still cutting my teeth on EasyEDA so this might be a real newbie question...but here goes.
I'm trying to simulate a relatively complex circuit comprising multiplexers and opto-couplers.  This was not behaving as I expected it to, so I thought I'd try testing one component at a time, starting with a single opto-coupler.
I created a
simple schematic containing a single TLP175A opto-coupler and connected its 'switching' terminal to a +5V supply.  I connected a 25V supply to the device's input and since the TLP175A is switched on I expected to see 25V on its output terminal.  However, I get 0V, i.e. the TLP175A doesn't appear to be turning on.
What I believe should happen is the following.

  1. Set the input to 0V, TLP175A output should also be 0V
  2. Set the input to +5V, TLP175A output should be +25V

Any ideas on what is going on here?  Is it my schematic, or is there an issue with the simulator not handling the TLP175A device?

Any feedback is most welcome.

#Simulation#
Circuit Design