I am designing a small breakout board for a power supply I am building. this small board will house a few resistors, a usb connector an arduino nano, and a header for supplying juice and other unimportant connections.
Problem: When i go to lay this out on pcb, It appears that a few of the connections in the rats nest are switched.
on the schematic:
- header pins 3 through 10 go to the analog inputs on the nano
- all of the digital pins are supposed to go to the display, excluding the four traces without a resistor.
on the pcb layout named vertical 2.5x1.5:
- d9 and d11 go to the female header for some reason
- thus R5 and R9 are not connected to D9 and D11
- And A5 and A4 are not connected to the Header
I appreciate your time looking over these things and appreciate any help you may provide!
https://easyeda.com/avfinchum/USB_Charger_Breakout_Board-ee6d38f9c70145b9b793b7915ed87323
#PCB#Hi,
I have a strange problem with a PCB I received recently (https://easyeda.com/editor#id=258bfeb9cae04acc8f60f8c3210fad20|fa47dea4c3514aa68e8eaebce54397db).
This is how it should look like (from EasyEDA PhotoView):
This is how it actually looks like:
(please ignore the cut traces - I tried to narrow down the problem by cutting off parts of the circuit).
As you can see the seven upper pads for the U_MODEM part are slightly displaced to the right, which resulted in a short-circuit with a trace going from north to south on the PCB.
The lower-most pad of the U_MODEM is at the correct position.
Did I do something wrong here, or is this some sort of bug?
I did put this in the "bugs" topic because I think that at least the Photo View should match the actual final PCB.
Thanks & Regards
Simon
Hello,
I nee d a N-MOS with a low Gate Threshold Voltage, but I did not found it in the library.
So,I wanted to create mine, based on the BSS138, and I found a Pspice model (below)
The problem is the simulation terminates with a timeout with this component (notwith another N-MOS).
So,I would like to know if my problem comes from my model.
Is there any warning or error message if there is a problem in the model ?
Thank you.
This is the model I found.
.SUBCKT bss138lt1 1 2 3
**************************************
* Model Generated by MODPEX *
*Copyright(c) Symmetry Design Systems*
* All Rights Reserved *
* UNPUBLISHED LICENSED SOFTWARE *
* Contains Proprietary Information *
* Which is The Property of *
* SYMMETRY OR ITS LICENSORS *
*Commercial Use or Resale Restricted *
* by Symmetry License Agreement *
**************************************
* Model generated on May 2, 03
* MODEL FORMAT: PSpice
* Symmetry POWER MOS Model (Version 1.0)
* External Node Designations
* Node 1 -> Drain
* Node 2 -> Gate
* Node 3 -> Source
M1 9 7 8 8 MM L=100u W=100u
* Default values used in MM:
* The voltage-dependent capacitances are
* not included. Other default values are:
* RS=0 RD=0 LD=0 CBD=0 CBS=0 CGBO=0
.MODEL MM NMOS LEVEL=1 IS=1e-32
+VTO=1.05059 LAMBDA=0.00404031 KP=0.269311
+CGSO=3.66018e-07 CGDO=7.50731e-09
RS 8 3 1e-15
D1 3 1 MD
.MODEL MD D IS=9.63839e-09 RS=0.186581 N=1.76759 BV=50
+IBV=0.00025 EG=1.11237 XTI=1e-12 TT=7e-08
+CJO=2.07759e-11 VJ=2.77485 M=0.3 FC=0.5
RDS 3 1 2.5e+09
RD 9 1 1.83726
RG 2 7 6
D2 4 5 MD1
* Default values used in MD1:
* RS=0 EG=1.11 XTI=3.0 TT=0
* BV=infinite IBV=1mA
.MODEL MD1 D IS=1e-32 N=50
+CJO=7.71436e-11 VJ=0.523477 M=0.9 FC=1e-08
D3 0 5 MD2
* Default values used in MD2:
* EG=1.11 XTI=3.0 TT=0 CJO=0
* BV=infinite IBV=1mA
.MODEL MD2 D IS=1e-10 N=0.4 RS=3.00002e-06
RL 5 10 1
FI2 7 9 VFI2 -1
VFI2 4 0 0
EV16 10 0 9 7 1
CAP 11 10 2.46901e-10
FI1 7 9 VFI1 -1
VFI1 11 6 0
RCAP 6 10 1
D4 0 6 MD3
* Default values used in MD3:
* EG=1.11 XTI=3.0 TT=0 CJO=0
* RS=0 BV=infinite IBV=1mA
.MODEL MD3 D IS=1e-10 N=0.4
.ENDS bss138lt1#Simulation#BUG
Concise problem statement:
I have created a spice model for the LM1117 LDO (subckt from this page: http://www.ti.com/product/LM1117/toolssoftware )
Steps to reproduce bug:
-
Open this schematic: https://easyeda.com/editor#id=917ba1fc12b04601bcdc1074ebb82fc2
-
Run the simulation
Results: Server Error (500)
Expected results: Successful simulation run!
#Bug Reports#